• Join the pressure regulator to the entrance threads of the Gas Manifold with gasket supplied with this appliance. The regulator is marked with a directional arrow indicating correct direction of gas flow. Ensure the appliance regulator is installed with the arrow pointing toward the gas manifold entrance and make sure the top of the regulator is facing towards the cabinet front, easily accessible through the cabinet doors. • Connect a manual shut-off valve to the gas supply in an accessible lo

13" (33 cm) MAX DEPTH WALL COVERING CABINETS, OF UNPROTECTED AND COUNTERTOP MUST OVERHEAD CABINETS WITHSTAND HEAT UP TO 200 °F MIN 30" (76.2 cm) 30" (76.2 cm) MIN (see NOTE) CLEARANCE FROM COUNTERTOP TO UNPROTECTED OVERHEAD SURFACE 18" (45.7 cm) MIN HEIGHT FROM COUNTERTOP TO NEAREST CABINET ON EITHER SIDE OF UNIT 003 5" (12.7 cm) MIN CLEARANCE FROM CUTOUT TO SIDE WALL ON THE LEFT AND RIGHT OF THE UNIT Figure 3. Cutout requirements NOTE: • If cabinet has a drawer, a 5-1/4"(13,35 cm) depth clearan

(any gas), an external regulator must be installed in the gas line ahead of the appliance regulator to reduce the pressure to no more than 14 inches W.C. Failure to do this can result in malfunction and damage to the appliance. Important Notes for Gas Connection The appliance and its individual gas shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa). The appliance must be isolated from th

• Ensure the countertop is square and level and ensure no structural members interfere with space requirements. • Prepare the cut-out according to the instructions (see cut-out dimensions). • Make sure the wall coverings, countertop and cabinets around the cooktop can withstand heat (up to 200 °F). 006 Figure 6. Tools you will need Step 1 Remove packaging materials and literature package from the cooktop before beginning installation. Remove Installation Instructions from literature pack and rea

See gas supply requirements. WARNING BEFORE CONNECT THE APPLIANCE ON THE GAS LINE SUPPLY, ENSURE THAT ITS GAS SET IS APPROPRIATE. THE TYPE OF GAS ADJUSTED AND SHIPPED FROM THE FACTORY IS INDICATED ON THE RATING PLATE LOCATED ON BOTTOM OF BURNER BOX. Cooktop Installed over Oven Installation Only certain specified cooktop and oven models are approved for cooktop over oven installations. Cooktops approved for this type of installation will have an approval label located on the outside of the burner

18 Burner Ignition................................................................... 18 manual: DANGER You can be killed or seriously injured if you don't IMMEDIATELY follow instructions. WARNING • This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. • You can be killed or seriously injured if you don't follow these instructions. READ AND SAVE THESE INSTRUCTIONS. To installer: Leave these instructions with the appliance. To costumer:

Make sure the front edge of the counter top is parallel to the cooktop. Make final check that all required clearances are met. Figure 9. Step 6 Loosen the screws, rotate the brackets so that they extend beyond edge of the burner box. Tighten screws securely. Figure 10. Installation Manual Models ECCB/TCCB 30” – 36” ENGLISH Figure 11. Figure 12. WARNING THE CONDUIT IS 3 FEET LONG The junction box, must be located where it will allow considerable slack in the conduit for serviceability. Models ECC

Porcelain enamel on steel or cast Iron: See stainless steel or cast iron. Stainless steel: Heats quickly, but unevenly. A core or base of aluminium or copper on stainless steel provides even heating. Match Pan Diameter to Flame Size The flame should be the same size as the bottom of the pan or smaller. Do not use small pans with high flame settings as the flames can lick up the sides of the pan. Oversize pans that span two burners are placed front to rear, not side to side. Use Balanced Pans Pan

There Elements will cycle on and off by the its own temperature limiters. Temperature limiters Each radiant heaters has its own sensor to protect the glass cooking surface from extreme high temperatures. The limiter will operate automatically by cycling the element the cycles as defined by knob setting (HI-LO) DUAL RADIANT ELEMENT The dual element consist of two radiant ribbon elements within the same heating area. Either the small (inner element) or both (inner and outer) elements may be select

They should never be allowed to sit or stand on any part of the appliance. CAUTION Do not store items of interest to children in cabinets above a range or on the backguard of a range; children climbing on the range to reach items could be seriously injured. When using the cooktop • Do not touch surface units or areas near units. Surface areas may become hot enough to cause burns. Surface elements may be hot even though they are dark in color. During and after use, do not touch or let flammable m