• Ding-Dong (two note tune) Push Button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected chimes) Push Button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note:All modelshave bothfrontandbackdoortunecapabilities.Werecommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected chimes). Models that include two push buttons will come facto

Sound travels farthest with the fewest obstacles. Do not place over heat source; i.e., radiator, heater, or stove. At the chosen location drill two small pilot holes 3 1/4" apart in the vertical plane. The chime cover is a push fit onto the base. Remove chime cover to expose base. Position base and mount in place using screws supplied, key-hole shaped slot at the 1 32 Base Plate Chime Cover top (see Figure 1). Figure 1 WIRING THE CHIME To Push Button A. Battery Operation. Do not use with lighted

No Service Parts Available for this Product Regulatory Information This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes or modifications not expressly approved by the party responsible for regulatory compliance

• Battery powered push button -No wires to run. • 128selectablecodesallowmorethanonechime system in the same house. © 2007 598-1077-02 Use either screws or double sided tape to mount push button. To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 1. Install alkaline type A2

If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. 2. Plug-in the doorbell chime. Chime Volume Control 1. Set the chime volume on the back of the plug-in chime, if desired. 3. Before mounting, test the doorbell range. Plug-in the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Access Door Ope

If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. 2. Plug-in the doorbell chime. Chime Volume Control 1. Set the chime volume on the back of the plug-in chime, if desired. 3. Before mounting, test the doorbell range. Plug-in the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Access Door Ope

• Battery powered push button - No wires to run. • 128 selectable codes allow more than one chime system in the same house. • LED lighted push bar (see Lighted Push Bar Feature). Lighted Push Bar Feature This ACE® wireless push button contains a LED (Light Emitting Diode) that will illuminate in dark conditions so the push button will be more visible for your guests. This (patent pending) technology and built-in photocontrol will allow the light intensity of the push button LED to increase as th

(Volume control feature is available on selected chimes). 2.Testrange.Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. WirelessPlug-InChimeAccessoryReceiverModel3106978(AC-6196) This package includes (Style of chime may vary from illustration): • Wireless chime • Hardware pack Chime Volume Control (Depending upon model) Access Door 3.Setchimevolume.Locate control on back of plug-in chime. (Volume control feature is available on select

• The non-electric chime mounts directly through the door and will accommodate door thicknesses of 3/4" to 2". • The chime is equipped with a viewer. Locating the door chime 1. Mount the chime in the center of the door approximately 4 1/2 feet to 5 feet above the floor. Note: Be sure there are no obstructions on the inside of the door to interfere with the chime’s baseplate. 2. Using the template provided, mark the location of the mounting holes parallel to the edge of the door (see Figure 1). N

In typical use, alkaline batteries will last three years. 3.Test Range. Temporarily position chime where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. 1. Open chime case: Press in catch on bottom of chime and lift the case open. Battery Chime Volume 2. Install the 3 alkaline "D" batteries. Make sure batteries are oriented properly. 4. Mount accessory chime. Chime can be mounted by using 3 holes in the back of c