The Power-On Indicator, on the front of the heater, will illuminate when the heater is turned on. Remove any promotional material or packaging from the heater. Unwind the cord to its full length and place the heater on a firm, level surface in a stable upright position. Visually inspect the air inlet and outlets to ensure there are no blockages. Assembling Your Heater Remove all items from the packaging - the carbon tower body, front and rear bases. Unscrew the two screws from the base of the to

Convenient 8hr auto-off timer 7. 2 heat setting, plus auto mode and fan only setting 8. 90° degree oscillation for warmth throughout the room 9. On/Off button and variable temperature dial, to turn the heater on and off and to maintain your desired temperature setting 10. Power-On indicator Not Shown • Convenient carry handle • Safety tip-over cut-out switch KCE440_IB_FA.indd 6 12/10/09 2:26 PM Quick Start Guide The heater will start operating at the HIGH heat setting. Leave at HIGH until the ro

Turn the heater on by switching the Power ON/OFF switch located on the back panel of the heater, to the ‘ON’ position. An audible beep will sound. The heater is now in standby mode. Using The Remote Control Your heater may be operated using either the control panel or the remote control. The remote control uses 2 x AAA batteries. To access the battery compartment, simply remove the cover at the rear of the remote control. To operate, ensure that you point KCE640_IB_FA.indd 8 16/10/09 10:50 AM Us

Since a fire risk may exist if the heater is covered or positioned incorrectly. 12. This heater is not intended for use in wet or moist locations. Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool. Do not immerse or allow liquids to be spilt on heater. 13. This heater has hot and arcing or sparking parts inside. Do not use in areas where petrol, paints, aerosols, or other inflammable substances are used or stored. 14. Do not operate the heater with the p

Regularly inspect the supply cord, plug, control settings, air inlets and outlets and main housing for any damage. If found damaged in any way, immediately cease use of the heater and return to Kambrook or an authorised service agent for inspection or repair. The installation of a residual current device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceedin

• Avoid placing items too close to the heater (both at the front and back) for optimal air flow Using Your Ceramic Heater Before First Use Remove any promotional material or packaging from the heater. Unwind the cord to its full length and place the heater on a firm, level surface in a stable upright position. Visually inspect the air inlet and outlets to ensure there are no blockages. Turning Your Heater On Plug the cord into a 230V or 240V power point and switch on. NOTE: To avoid an electrica

NOTE: After several seconds, the LCD screen will fade, but the heater settings will remain visible. Use the MODE button to select the desired heat setting. The mode button allows you to scroll through the various heating modes. HIGH – High heat setting (1800 watts) LOW – Low heat setting (1100 watts) AUTO – for use with the electronic thermostat FAN – for fan only operation To switch the heater into standby mode, press and hold the POWER/ SWING button until a beep sound is heard. Turn the heater

3. This heater has three heat control settings OFF, ”LOW” HEAT AND “HIGH” HEAT, located at the top of the unit, along with an adjustable thermostat control. “LOW” HEAT (750W) is the lowest heat setting and “HIGH” HEAT (1500W) is the highest. 4. To select these settings DO NOT twist or rotate the heat control and thermostat control located on the top of the heater. To turn the heater on, grip the heat setting knob and lightly pull all the way up to the “HIGH” setting. There will be an audible cli

• Do not touch hot metal surfaces. • Do not allow power cord to contact hot metal surfaces. • Set the control setting to the OFF position then Unplug and allow heater to cool down before cleaning or storing. • The heater will not operate unless it is placed on a flat level surface as it is fitted with a tilt switch. • Do not use the heater with a programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorr

Heater elements 2. Safety grill 3. Carry Handles 4. Control dial 5. Tip over switch BEFORE USING YOUR RADIANT HEATER, PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE REFERENCE. 1 IMPORTANT SAFEGUARDS When using electrical appliances, basic precautions should always be followed, including the following: • To prevent a possible fire, allow ample space around the heater (at least 1.7m at front and 0.5m at the rear, top and • Keep combustible materials such as curtains/drapes and othe