It will set the room air blower speed to high at any feed rate setting. • When the “HIGH FAN” button is pushed the room air fan will switch to its highest setting. • When this button is pushed again the room air fan will return to its original setting based on the Heat Level Advance setting. • If the “HIGH FAN” setting is used for extended periods of time it can shorten the life expectancy of the room air fan. Avoid use at this setting for more than one hour at a time. d. RESET TRIM Different si

Pedestal: 40 lbs. Legs: 13 lbs. Flue size: 3” or 4” Hopper Capacity: Up to 60 lbs. (this can vary widely depending on pellet size, length, and diameter) EPA status: exempt Burn time: 1 lb. to 5 lbs. per hour BTU range: 8,200 to 47,000 Approved installations: mobile home, alcove, conventional FIREPLACE INSERT: Width: 21” (With flashing: 42”) Height: 20” (With flashing: 30” or 32”) (depending on which size of flashing used) Depth: 22 .” In fireplace: 11 .” Weight: 185 lbs. Flashing: 13 lbs. Flue s

Pedestal: 40 lbs. Legs: 13 lbs. Flue size: 3” or 4” Hopper Capacity: Up to 45 lbs. (this can vary widely depending on pellet size, length, and diameter) EPA status: exempt Burn time: 1 lb. to 4 . lbs. per hour BTU range: 8,200 to 40,000 Approved installations: mobile home, alcove, conventional FIREPLACE INSERT: Width: 21 .” (With flashing: 39”) Height: 20” (With flashing: 30”) Depth: 24” (In fireplace: 10 .”) Weight: 185 lbs. Flashing: 13 lbs. Flue size: 3” or 4” Hopper Capacity: Up to 45 lbs. (

If the voltage is lower than full current, check the wiring. If the wiring checks out good, the board is bad. SMOKE SMELL COMING BACK INTO THE HOME Possible Causes: Possible Remedies: 1. There is a leak in the vent pipe system. Inspect all vent pipe connections. Make sure they are sealed with RTV silicone that has a temperature rating on 500 degree F or higher. Also, seal joints with UL-181-AP foil tape. Also, make sure the square to round adapter piece on the combustion blower has been properly

per hour to help you plan your refueling schedule. Please note these rates are only approximate. The "Max" setting feeds approximately 4Vi lbs./hour. The convection blower speed varies directly with feed rate. The "High Fan" switch overrides this variable speed function. It will set the convection blower speed to high at any feed rate setting. 3.5 Optional Thermostat A remote thermostat will help you maintain a constant house temperature automatically. A low voltage, normally closed thermostat

Poor quality pellets could damage the auger. Breckwell cannot accept responsibility for damage due to poor quality pellets. Your dealer can recommend a good quality pellet dealer in your area. PRE-START-UP CHECK Remove burnpot, making sure it is clean and none of the air holes are plugged. Clean the firebox, and then reinstall burnpot. Clean door glass if necessary (a dry cloth or paper towel is usually sufficient). Never use abrasive cleaners on the glass or door. Check fuel in the hopper, and

If only the 1 light is on, the stove is in the default (medium) setting. If the 1 & 4 lights are on, the stove is in the high trim setting for the low feed rate. If the stove is being burned on one of the two lower settings, advance to the next trim setting and try burning the stove. 28 8 TROUBLESHOOTING GUIDE HIGH LIMIT SWITCH KEEPS TRIPPING Possible Causes: Possible Remedies: 1. The convection blower is overheating and tripping the internal temperature shutoff. Clean any dust off of the windin

A hinged door oovers the panel during normal operation. The on-off switch turns the blowers on. The “auger" button activates the automatic feed system. When the green light is on, there is power to the auger circuit. The auger will not begin feeding pellets until the firebox has warmed up to a preset temperature. In case of a power outage lasting more than three to six seconds, this button must be pushed to re-engage the auger. There are six fuel feed settings. On “LOW”, the feed rate is approxi

For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. Factory Recommends Professional Installation ALL UNITS TESTED AND Manufactured by National Steelcrafters of Oregon Inc. _ ^ ^ __ . __ ÔfMTfONAL STEELCRAFTERS OF $ P.O. Box 24910 oneûûNiNc icBOTL-116 NER-QA-219 Eugene, Oregon 97402 3S7 1000 PAGE 1 Thank you for purchasing the Breckwell Pellet Burning Stove. You are now pr

Airflow switch hose or stove attachment pipes for hose are blocked. Unhook air hose from the air switch and blow through it. If air flows freely, the hose and tube are fine. If air will not flow throw the hose, use a wire coat hanger to clear the blockage. 2. The air inlet, burnpot, interior combustion air chambers, combustion blower, or exhaust pipe are blocked with ash or foreign material. Follow all cleaning procedures in the maintenance section of the owner’s manual. 3. The firebox is not pr