By allowing you to convert even the highest bit rate digital signals from coax to optical or vice versa, Audio Authority's digital audio converters provide maximum fidelity and compatability. 977T coaxial input Model 977RPO Digital Optical to Digital Coaxial Converter The 977R (Receiver) converts the optical audio output of a digital source (DVD player or satellite receiver) to coax for connection to Dolby Digital® or DTS® receivers. 977RPO FEATURES & SPECIFICATIONS: • Reliably converts di

The Model 1185ci is the first Audio Authority distribution amp expressly designed for Custom Installers of Home Theater systems. It includes the most-asked-for features, such as ultrawide video bandwidth, audio channels that also pass sync for RGBHV displays, and full optical/ coaxial support of digital audio with automatic conversion. Housed in a durable steel enclosure, the Model 1185ci also has side-looking input and output jacks for extra compact cable routing. Audio Authority also offers an

Connect bus jacks for all channels whether or not they will be used. Pull two cables to each wallplate location, preferably using a different colored cable jacket for A and B cables. Install an RJ-45 termination on each end of every Cat 5 cable, using EIA-568B pairing (pins 12, 3-6, 4-5, 7-8). If possible, use EZ RJ-45 connectors. Check each cable with a network cable tester – CONTINUITY TESTING IS NOT ADEQUATE – the pairs must match the EIA-568B color code. WHT / ORNORNWHT / GRNBLUWHT / BLUGRNW

Adjust the cable length compensation if the cable between the Driver and the wallplate/receiver is over 100 feet long. Set the compensation at 1 for cables 100-199 ft. long, and 2 for 200-299 ft. cables, etc. Do not permanently mount the wallplate/receivers until after system testing. Carefully connect the A and B cables to the Driver(s), power the source components, TVs and AV receivers, and plug in 9871 power supplies to test the system. Connect a TV to each wallplate/receiver location to refi

Like other members of the 985 family, 985DTV modules can be cascaded to allow virtually an unlimited number of television monitors to be driven from a single source without picture degradation. The exceptional bandwidth of this product supports video standards from today on into the future. The 985DTV can also be used for RGB video distribution in video production and duplication facilities. Digital audio distribution complements the 985DTV's video capability by providing lossless transmission

Component video (YPbPr), analog stereo audio, and digital audio (coaxial) sigals are included in each two-cable Cat 5 pathway. By connecting IR remote control systems to the DuoDrive system, users can easily control the source equipment from other rooms in the house. IR receiver and emitter products are not included with the DuoDrive. System Design The DuoDrive is comprised of one Model 9871 RCA-to-Category 5 Driver and two Model 9879 wallplate/receivers. (Two other Cat 5 receiver styles are als

It makes no difference if selection of product is by Control Panel or by Product Select Buttons or both, therefore, always follow this diagram for proper setup. Concerning signal path, the Model 980EZ will be located just before the amplifier inputs (see Appendix A). In the 2-channel configuration, the Front Inputs and Front Outputs are the only connections that are used. In the 6-channel configuration, all three sets of inputs/outputs are used. The Low-Level buses (e.g., front, rear, sub) conti

If a receiver does not have some of the features shown, simply leave those jacks or terminals vacant on the 947. Always connect the A/V cables to the VCR 1 or Video 1 jacks on the receiver. To prevent a blank screen when switching from a GUI reciver to a non-GUI receiver, you should install a 986 Video AutoPatcher in your system. There is no optical digital connection on the 947 - use the coax input on digital audio receivers, or use Model 977T Coax to Optical Adapter. Instructions for other typ

If you find any items are missing, contact Audio Authority immediately. Have the Model Number, Serial Number and Invoice available for reference when you call. 4.0 CONNECTING THE HARDWARE Please study the panel drawings below and become familiar with the signal input(s), output(s) and power requirements. Model 1311 DVI + Digital Audio to HDMI Converter Model 1312 HDMI to DVI + Digital Audio Converter 5.0 OPERATING THE UNIT Before installation, please make sure all devices you wish to connect hav

Install an RJ-45 termination on each end of every Cat 5 cable, using EIA-568B pairing (pins 12, 3-6, 4-5, 7-8). If possible, use EZ RJ-45 connectors. Check each cable with a network cable tester – CONTINUITY TESTING IS NOT ADEQUATE – the pairs must match the EIA-568B color code. WHT / ORNORNWHT / GRNBLUWHT / BLUGRNWHT / BRNBRN CATEGORY 5,5e or 6 CABLE Note: EIA 568A or B standard may be used. (B is pictured here.) Make sure both ends are terminated with the Category 5 Connector Termination This