Do not remove wheels or feet. 3. Fit plinth by inserting the top flange of plinth (the flange with the 16 notches) between the base panel and dryer cabinet bottom flange. Fit front flange first springing the sides outward to assist assembly. 4. Adjust plinth to fit flush with the cabinet then tighten screws. 5. Fit front and rear beams using the screws provided. 6. Remove screws from lower rear panel and re-use to fit back plinth panel. Also use screws supplied to secure sides and bottom edg

This set of instructions is general: local building codes take precedence over the instructions in this guide and your installation must conform to the building codes in your area. Be sure to retain this set of instructions for future reference. TOOLS REQUIRED FOR INSTALLATION You may need the following tools and supplies when installing your disposer: (ILLUSTRATION #1) Pipe wrench Hacksaw Plumber’s Rod Phillips Screw Driver Rubber Mallet Electrical Switch (20 amp rating) -3 - UNPACKING YOUR WAS

For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer. Introduction Congratulations on the purchase of your new Ceramic Cooktop. We strongly recommend that you read this User Guide carefully to take full advantage of the features offered by this product. This books covers operational instructions for the CT560, CT655 and CT280 series ceramic cooktops. Safety instructions WARNING! Electrical Shock Haza

Spillovers Clean the following spillovers immediately, using the razor blade scraper provided. Do not let sugar, jam, plastic, plastic wrap and aluminium foil melt onto the cooktop surface. Clean these immediately using the razor blade scraper provided. Anything that melts onto the glass surface may cause pitting if it is left to cool before removing. Pitting may also occur when a food with a high sugar content is spilt onto the cooktop and not cleaned up immediately. Turn the element off, caref

To turn your cooktop on, touch the button with the ball of your finger for approximately 3 seconds. You will notice all the element indicator displays will come on with and a small flashing red light. Using the elements 1 With the cooktop turned on, touch the corresponding element button in the touch controls for the element you wish to cook on. 2 The red light will stop flashing and remain static, beside the element that is selected. (If no element is selected within 5-10 seconds the cooktop wi

The dust hood adjusts vertically from 29" to 49". Figure 1. Model T10117 identification. Inventory After removing the contents of the shipping package, lay them out and refer to the Parts Breakdown on the back page to inventory the components. If you need help with your new dust hood, call our Tech Support at: (570) 546-9663. Assembly Refer to Figure 1 and the Parts Breakdown illustration to aid you in the following assembly procedure. Tools Needed Qty Wrench or Socket 10, 14mm.........

INSTALLATION INSTRUCTIONS CONTENTS Contents of packaging Equipment required Optional accessories 1 x canopy hood Electric drill Light bulb 104467 2 x chimney pieces Drill bits Chimney ext. (10’ ) SS 8 x angle brackets Spirit level Chimney ext. (10’ ) IR 1 x installation instructions Screwdriver Charcoal filter 103821 4 x filters ( part number 104660) Jig saw Recirculation kit 1744 Installation kit ( part number 104922) Ladder 4 x 12 x 40mm screw Tape measure 30 x 6 x . ” self tapping screw Duct

• To comply to electrical safety regulations this canopy must be plugged into a socket near the appliance. The socket must be accessible and enable the end user to isolate the canopy from the power for the purpose of internal cleaning or maintenance. Ducting accessories are not supplied. All ducting must comply with local requirements and building codes. The canopy hood is heavy please ensure adequate care when installing the canopy hood to prevent personal injury. The canopy hood must be instal

13. Connect to the power supply and switch on the power using switch/socket outside the canopy hood. 14. Slide the upper chimney piece up to the ceiling and secure in place with four screws supplied. INSTALLATION – RECIRCULATED For recirculation do not cut the 170mm hole into the ceiling and purchase the charcoal filters and recirculation kit 1744. The recirculation kit must be used to channel the air to the top of the flue. For other accessories parts and service please contact your local suppl

a. When fitting to a 50mm truss drill a pilot hole through the ceiling and into the truss. b. If securing to any other ceiling type please use appropriate fasteners and follow their instructions of use carefully. 5. For the ducting mark out and cut a O170mm hole in the ceiling. 6. Fix the ceiling bracket to the ceiling using the screws supplied. 7. Using duct tape secure the ducting to the top of the motor housing. Solid ducting, galvanized or plastic is recommended. Use flexi ducting only in di