If you purchased the product for use primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) normal wear and te

Turn to page 11 to continue the installation. English English Install the handle Push the handle over the valve stem. Tighten the handle screw using a 3 mm Allen wrench. The handle screw must engage the slot milled into the cartridge. Install the handshower Place a black rubber washer one end of the hose. Connect this end to the handshower outlet on the panel. Place the screen washer in the other end of the hose. Connect it to the handshower. Place the handshower in the handshower holder. Adjust

Push the function lever until the desired spray mode is achieved. the bodysprays. function lever 15 Scale removal The Raindance Air 3-jet handshower incorporates the Quick Clean™ cleaning system. If scale deposits are noticed in the spray channels, turn the water on lightly and rub the spray channels with a finger or a sponge. If scale deposits are noticed on the spray face, pour about 3/4” of a commercial scale remover, such as Lime-Away™ or CLR™ ,into a shallow dish. Dilute the remover accordi

Failure to seal the wall can lead to possible water damage. 9 10 11 12 2 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. Be careful not to drill into water lines! 6 mm 1 13 14 Install the 26397000 mounting set 16 15 17 18 XX90XX= 20 19 22 21 1 2 6 mm SW 3 mmM6x8 24 23 M6x601.2.3. SW 3 mmM6x8 25 26 Install the 26397000 mounting set 27 28 2 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can le

Tow remove the temperature control disc, together with the wavy washer. The control disc houses the maximum temperature stop mechanism (fig.80). To increase the temperature stop setting, reposition the temperature stop mechanism clockwise within the arc of the grooves (fig.80). To decrease the temperature stop setting, reposition the stop mechanism anti-clockwise within the arc of the grooves. When the stop mechanism is set at the preferred position, refit the temperature control disc making s

Protection against back siphonage provided by check valves. The check valves should be removed and inspected yearly (see page 8). This panel may be used with an instantaneous water heater if the heater is at least 24 kW and the output is at least 3 gpm @ 30 psi pressure. However, only one panel function may be used at a time. *Please know and follow all applicable local plumbing codes when setting the temperature on the water heater. In Massachusetts, the water heater may be set no higher than 1

Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage. Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty. Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United Stat

If scale deposits are noticed in the spray channels, turn the water on lightly and rub the spray channels with a finger or a sponge. If scale deposits are noticed on the spray face, pour about 3/4” of a commercial scale remover, such as Lime-Away™ or CLR™ ,into a shallow dish. Dilute the remover according to the label instructions. Soak only the spray face in the solution for the amount of time specified on the label. Rinse the handshower with clear water. Reinstall the handshower. Turn on the w

24 kW and 29 psi flow pressure before the Shower panel. Only one consumer possible, not two simultaneously. Pressure differences: The pressures of the cold and hot water connections must be balanced. Maintenance The non return valves must be checked regularly according with national or regional regulations (at least once a year!). * Check applicable codes The flow rates are limited to .5 gpm. These are the maximum flow rates permitted by the From • the function is guaranteed. Fitting Items / Wat

Screw the hose to the handshower. If the flow of water becomes noticeably less, remove and clean the screen washer. Scale Removal The Raindance Air 3-jet handshower incorporates the Quick Clean™ cleaning system. If scale deposits are noticed in the spray channels, turn the water on lightly and rub the spray channels with a finger or a sponge. If scale deposits are noticed on the spray face, pour about 3/4” of a commercial scale remover, such as Lime-Away™ or CLR™ ,into a shallow dish. Dilute the