Argument: None. Possible value: None. Example: None. save start Syntax: save start Description: To save the current configuration as the startup configuration. When you enter this command, the CLI will save your current configuration into the non-volatile FLASH as the start up configuration. Argument: None. Possible value: None. Example: GSM-16T2SFP# save start Saving start... Save Successfully GSM-16T2SFP# 120 Alloy Computer Products Pty Ltd Copyright ©2006 GSM Series User Manual save user Synt

Click the button for changes to take effect. Prioritise web browsing, email, FTP and news: Check this radio button to prioritise web browsing, email, FTP and news services over all other services. If you want to customise the ports that are in use by this built in service click on the advanced tab to make the necessary changes. Click the button for changes to take effect. Prioritise Streaming Audio/Video: Check this radio button to prioritise Audio and Video streaming services ov

OVERVIEW OF GSM SERIES SNMP MANAGED SWITCHES ..................................................2 1.2. CHECKLIST .......................................................................................................................3 1.3. FEATURES ........................................................................................................................4 1.4. OVERVIEW OF GSM SERIES SWITCHES .............................................................................5 1.4.1. User Int

OVERVIEW OFTHE POEGEM12T2SFPSNMPMANAGED POE SWITCHES........................2 1.2. CHECKLIST .......................................................................................................................4 1.3. FEATURES ........................................................................................................................4 1.4. OVERVIEW OF THE POEGEM12T2SFP SWITCH................................................................5 1.4.1. User Interfaces on the Front Panel (

Introduction ............................................................................................................... 2 2. Safety Notification .................................................................................................... 3 3. Hardware Installation................................................................................................ 4 4 Web Management Settings ....................................................................................... 5 4.1. Set

When you use an Ethernet cable to connect other devices, such as computers, switches or hubs, pin 1, 2, 3, and 6 of the 8-pin RJ45 connector are used to communicate with the connected devices. Pin1, 2, 3, and 6’s signals are converted by the MDI-X function, as shown in Table 2. Pin MDI-X Signals MDI Signals 1 RD+ TD+ 2 RD- TD- 3 TD+ RD+ 6 TD- RD- Table 2 Cabling The cable connection between the RNS5/8 and the attached devices (switches, hubs, workstations, etc.) must be less than 100 meters (328

Harsh temperature conditions, vibration, dust, etc. all put higher demands on the quality and reliability of your networking equipment. To survive harsh industrial environments, Alloy provides you with the RNS5/8 Series Industrial 5-port/8-port 10/100Mbps Ethernet Switches. The RNS5/8 Industrial switch is a cost-effective solution ideal for your industrial applications in harsh environments. The RNS5/8 not only gives you high speed data transmission over an Ethernet network, but also provides re

VP then 25 will display PVID = 1 In the case that you do configure this state and lock the web interface out, then you can recover by connecting to the RS-232 console port and either disabling Tagged VLAN, or adjust the settings via the following options. VE - Enable/Disable 802.1Q VLAN VF – Get 802.1Q VLAN Enable Setting VV – Set PVID VP – Get PVID 19 2.6.1 Enable/Disable VLAN In the 802.1Q VLAN page, you can enable/disable the tag-based VLAN function by clicking the (Enable) or (Disable) hyper

4 1.1 Managing The Switch ................................................................................................. 6 1.2 Configuration of the Switch ....................................................................................... 7 2 Configuration .............................................................................................................................. 8 2.1 Port Status ...........................................................................................

CONFIGURATION This Switch is an unmanaged, but “smart” Switch because programmable administration parameters make the Switch operate more effectively than unmanaged (dumb) switches. This chapter will describe how to configure the Switch. Console Port (RS-232 DCE) The console configuration requires connecting a terminal, such as a Workstation or a PC running a terminal emulation program (such as HyperTerminal, which is automatically installed with Microsoft Windows) a to the RS-232 DCE console po