(end of range) and rollover. After rollover, use Master Reset. ACCUSPLIT, Inc. 3090 Independence Drive Suite 148 Livermore, CA 94551 USA 800-935-1996 • 925-290-1900 FAX 925-290-1930 support@ACCUSPLIT.com ? I? *■* o ,© © — ’T tS p-T support@accusplit.com ASSEMBLED IN HONG KONG ©2005 ACCUSPLIT ^

S' ' 3 30 B»ï-, S £ I I____I /1EEU5PLIT 705MX OPERATING INSTRUCTIONS BASIC STOPWATCH OPERATIONS Master Reset R+L (2sec) - Reset** All segments go blank, then come on briefly. Event R-Start R-Stop (Display shows “SPLIT") R(2sec) - Reset** Dual Split Memory with Split Counter R-Start (Shows Running DUAL Time) R-Split* (Top shows CUM 1, Bottom shows LAP 1) R-Split* (shows CUM 2, Bottom shows LAP 2) R-Split* (Top shows CUM 3, Bottom shows LAP 3) R-Split* (Top shows CUM 4, Bottom

(There is no alarm for this setting, as it will continue to count up until it is stopped.) - Press the START-STOP button to STOP count-up. PRODUCT SPECIFICATIONS Operating Temperature: 14°F-138°F (-10°C - 59°C) Battery: - When LCD Display becomes dim, replace battery with LR-44 or equivalent. - 18-Month Circuit Battery Life (reduced dependent on extensive alarm usage). ACCUSPLIT, Inc. 3090 Independence Drive,, Suite 148 Livermore, CA 94551 USA 800-935-1996 • 925-290-1900 • FAX 925-290

increments (0-99). - Enter Seconds by pressing SEC button in one sec. increments (0-59). - Repeat as necessary. STARTING AND STOPPING COUNTDOWN FUNCTION - Press the START-STOP button to START the countdown timer. - Press the START-STOP button to STOP the countdown timer. STARTING AND STOPPING COUNT-UP FUNCTION Starting from 00:00, - Press the START-STOP button to START count-up. (There is no alarm for this setting, as it will continue to count up until it is stopped.) - Press the ST

In addition, the stopwatch is water resistant. Therefore, it is suitable for aquatic sports or use in rainy weather. • STOPWATCH The stopwatch can measure up to 10 hours in 1/100 seconds. • SPLIT TIME/LAP TIME MEASUREMENT Up to 100 split times and lap times can be measured. 2 • LARGE-SIZED THREE-ROW DISPLAY PANEL Total elapsed time, split time and lap time are displayed at the same time in separate rows, and they can be measured successively without releasing split or lap time measurement. • MEM

The fields are: Time setting Alarm On/Off Time setting. Press S2 until you see digits in the center of the display. Now you can set the timer. Press S3+ (lower right) to increase the timer set point, and press S3– (lower left) to decrease the set point. You will see both the digits and also the dial size increase or decrease. For a setting of 60 minutes, the dial will show completely red. Once you have set the desired time, press S2 once to change Alarm On/Off Setting. You will see the word “O

second). • To Reset the timer, press and hold the TIMER button for at least 2 seconds. If turned ON, the Alarm will sound when time expires. The alarm sounds for 5 seconds, or until cancelled by pressing any button. Setting the Timer The timer must be stopped before changing settings. The timer uses a standard setting procedure: • Press and hold “S1” to enter setting mode • Press “S2” to change the field to set • Press “S3” to change the value of the field being set • Press “S4” to exit setting

• To Stop the timer, press the TIMER button TWICE, in rapid succession (press the button twice within . second). • To Reset the timer, press and hold the TIMER button for at least 2 seconds. If turned ON, the Alarm will sound when time expires. The alarm sounds for 5 seconds, or until cancelled by pressing any button. Setting the Timer The timer must be stopped before changing settings. The timer uses a standard setting procedure: • Press and hold “S1” to enter setting mode • Press “S2” to chang