Product Features ................................................... 2 Component Identification..................................... 3 Identify Your Door Type ........................................ 3 Important Installation Instructions........................ 4 Assembly Instructions........................................... 5 Installing the Opener ............................................. 7 Mounting the Front Bracket ................................ 7 Mounting the Power Head..............

2 WARNING HIGH VOLTAGE ONLY A QUALIFIED TECHNICIAN SHOULD SERVICE THIS GATE OPERATOR PERIODICALLY TEST SENSITIVITY OF OVERLOAD *** READ MANUAL *** DATES DATE TESTED DATE TESTED DATE TESTED DATE TESTED SERVICED LOG DATE OVERLOAD TEST Pre-Installation Notes................................................... 3 Operator Class Designation ................................... 3 Section A: Gate System Design/Installation ............. 4 Section B: Preparing the Site .....................................

Connect to terminals 0 and 1 as shown in the illustration below. Support the wire near the operator with wire ties. Step 5: Install the Control Button Warning Label supplied with your opener near the standard wall push button (see illustration next page). WARNING A CHILD OPERATING THE DOOR CONTROLS RISKS INJURY — OR DEATH — TO HIMSELF (HERSELF) AND OTHERS. DO NOT ALLOW CHILDREN TO OPERATE ANY DOOR CONTROLS. MOUNT THE PUSHBUTTON AT LEAST 5 FEET FROM THE FLOOR, OUT OF REACH OF CHILDREN. INSTALLATI

This action will erase any previous signal that was learned by the control board and prepare it to learn your transmitter signal. At this time have your transmitter ready to transmit. STEP 2: Press and quickly release the Learn Enable button on the Super Station. The red LED light on the rear panel of the power head unit (and the work light) will illuminate and remain on, the control board is now ready to learn the signal from your transmitter. Within a twenty second time frame, press the button

The Warning and Caution boxes throughout this manual are there to protect you and your equipment. Pay close attention to these boxes as you follow the manual. WARNING Indicates a MECHANICAL hazard of INJURY OR DEATH. Gives instructions to avoid the hazard. CAUTION Indicates a MECHANICAL hazard of DAMAGE to your gate, gate operator, or equipment. Gives instructions to avoid the hazard. Indicates an ELECTRICAL hazard of INJURY OR DEATH. Gives instructions to avoid the hazard. WARNING Indicates an

Bright transmitter LED's indicate operation and monitor battery condition. (Page 15) Deluxe Wall Push Button Station: A feature-packed accessory unit, Allstar's Deluxe Wall Push Button Station allows access to all of the Opener'sfunctions. The Opener's built-in light can be turned on or off independent of door operation. A Vacation Switch allows the Opener to be deactivated for extended periods of time. Lighted Push Buttons enhance nighttime use. (Page 16) Keyless Entry System: A tamper resistan

Close the door. If the down force adjustments are correct, the door will reverse within two seconds of contacting the object and travel to the Full Open position. If this does not occur, recheck the Limit Adjustments (Page 17) and Sensitivity Adjustments (Step 2 & 3, Above). NOTE: Any time adjustments are made to Limits or Sensitivity, YOU MUST RETEST THE OPENER FOR THE REVERSING FEATURE AT FLOOR LEVEL AS OUTLINED ABOVE. OPEN FORCE ADJUSTMENT CLOSE FORCE 104391 ADJUSTMENT 1 1/2” BLOCK OF WOOD LA

A small Plastic Pin is provided to secure the other end of the Receiver to the panel. For proper operation, the Antenna Wire should be POINTED STRAIGHT DOWN toward the floor. After installing the Radio Controls, check their operation by moving approximately 35 FT away from the garage door and pressing the Transmitter Button. Operation at this distance should be reliable. If the Transmitter doesn't activate door operation, check that all Coding Switches are set identically. If the operational dis

• ADJUST THE SENSITIVITY ADJUSTMENTS ENOUGH TO ALLOW THE DOOR TO OPERATE, BUT NOT SO FIRMLY AS TO EXERT EXCESSIVE PRESSURE ON AN OBSTRUCTION BEFORE REVERSING. • AFTER INSTALLING THE OPENER, THE DOOR SHOULD REVERSE WHEN IT CONTACTS A 1-1/2" HIGH OBJECT (A PIECE OF STANDARD 2 X 4 BOARD LAID FLAT) ON THE FLOOR. B: IMPORTANT INSTALLATION 7 WARNING SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE USED TO BALANCE YOUR GARAGE DOOR ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SEVERE INJURY OR DEAT