For installations in Massachusetts, Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult your licensed plumber for installation of this system. This system and its installation must comply with state and local regulations. The use of saddle valves is not permitted. If this is your first experience having soft, conditioned water in your home, you’ll be amazed at the marvelous difference it makes. We promise that you’ll never want to be without it again. Congratulations, too, on select

Equipment Needed • Safety glasses • Rubber gloves, sanitary • Wash cloth, clean and lint-free • Liquid dish soap • Household bleach - unscented only (5-1/4% sodium hypochlorite) • Plastic storage bag • Manual air pump • Plastic bucket • Plastic bowl • Silicone lubricant, FDA approved Have all components and supplies on-hand and ready before beginning procedure. A clean work area and equipment are essential to properly clean and/or sanitize the system (i.e., clean hands, tools, work surface and c

For the dealer nearest you, call 1-800-BUY-MOEN. Use only MicroTech filter cartridges with the PureTouch® Filtering Faucet System. Do not remove the filter until it is to be replaced. 1. Remove pullout spout (19) from receptor (15) and tie a dish towel around the hose to keep it from slipping back into the spout receptor. 2. Disconnect the quarter turn connector (18) from pullout spout by turning it counterclockwise one quarter turn. Quarter turn connector will remain on the hose. 3. Remove the

10.Pull pullout spout in and out to check for free movement of hose. If needed, adjust the placement of weight to aid the clearance of the hose. 11.Faucet flushing is required before installation is complete. (See below) LINE FLUSHING INSTRUCTIONS IMPORTANT: Pipe chips, sand, stones and other solids found in new and renovated plumbing can damage the sealing surfaces of the filter cartridge and cause a leak. To avoid damage, DO NOT TURN ON SUPPLY VALVES until instructed below. 1. Pull hose out of

.. . Easy to replace water filter integrated in pullout spout HELPLINE: 1-800-BUY-MOEN INS115D plate or single hole deck ring WELCOME TO MOEN® Congratulations! You’ve purchased the revolutionary PureTouch® Filtering Faucet System. This faucet is the first of its kind and is designed to provide great tasting, cleaner water with just one touch. To get the most enjoyment from your Moen PureTouch Filtering System, please read all installation and operating instructions carefully. With simple care an

• Single, Duplex, Triplex, or Quad Configurations • Regeneration initiation by choice of time clock, meter or differential pressure switch. • Carbon Filters – For reduction of organics (flow rates up to 39gpm), or chlorine (flow rates up to 77gpm). • Depth Filters – Flow rates up to 193gpm. • Top-Mounted Control Valve – Keeps plumbing connections simple and adaptable. Full flow porting with rounded orifices and wide-open cartridges promote good flow characteristics and low pressure fluctuations.

lb 870 1,150 1,750 2,530 3,550 7,000 8,800 10,800 18,500 25,000 kg 390 520 790 1,150 1,610 3,175 4,000 4,900 8,390 11,340 NOTES: 1 Service flow rates are based on 7 gpm/ft2 (26 L/m2/min) for Normal and 15 gpm/ft2 (57 L/m2/min) for Peak Flow rates. Actual service rate can vary from 2 to 20 gpm/ft2 (8 - 76 L/m2/min) depending upon the application and the raw water. 2 Backwash flow rates are based on 12-14 gpm/ft2 (45-53 L/m2/min) using 50° F (10° C) water. A different backwash rate may be required

–contact between sensor and factory for greater IQS/3 Controller distance requirements *Number of pipe diameters required adjacent to flow sensor location dependent on source of upstream turbulence: Electrical Output: *Requires DC Current from IQS/3;+5VDC @ 10 ma. Environmental: Ambient temperature Relative Humidity: Dimensions: X: 1/2" thru 4" = 3.50" 5" thru 8" = 5.00" 10" up = 7.75" ) 15 minimum/ 55 maximum Open Collector, transistor, sinking -40F to 1220F 0% to 100% Non-condensing *Refer to

As a manufacturer, we do not know the characteristics of your water supply or the purpose for which you are purchasing this product. The quality of water supplies may vary seasonally or over a period of time, and your water usage rate may vary as well. Water characteristics can also differ considerably if this product is moved to a new location. For these reasons, we assume no liability for the determination of the proper equipment necessary to meet your requirements, and we do not authorize oth

A wide variety of installation fittings are available to assure compatibility with many commonly used plumbing materials: •Threaded galvanized •Copper sweat •PVC; CPVC •Iron •Steel The XLF flow sensor package is comprised of: •One (1) paddlewheel insertion type flow sensor element sized for the specified pipe diameter •One (1) installation fitting for the specified pipe type and size. How It Works The solid state paddlewheel flow sensor works on a simple, but precise, electro- mechanical princip