3 -4 specifications .............................................................................................................. 5 product features ..................................................................................................... 5 unpacking and assembly ............................................................................................ 6 propane supply ........................................................................................................... 7 con

Note: If any of the origianl wire, as supplied with the appliance, must be replaced, it must be replaced with 105°C wire or it’s equivalent. OPERATING HEATER FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around t

With zone heating, you save 3% on your energy bill for every 1°-thermostat set-back. That’s 15% for every 5°! Your savings can total $312* annually. * Cost savings based on a 5° thermostat set-back. Calculations established on average natural gas/propane heating costs published by U.S. Department of Energy. Gas is still a better value than wood or electricity! $0.37$0.61$0.83$0.94Ideal for any season, new LED flame. Approved for use in any room of the home. Easy operation -Great value --Unparall

Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. 1. STOP! Read the safety information, abovc. 2. Make sure equipment s

Follow procedures described earlier for all other adjustments. Step 5 "@ ! 7 . 13.0) GAS CONNECTIONS AND REGULATIONS / ; . ; . BB / D . B . . . IMPORTANT BEFORE CONNECTING THE GAS TO THE HEATER 1. Connect to the supply tank or manifold in accordance with the latest edition of National Fuel Gas Code (ANSI Z223.1), and local building codes. Authorities having jurisdiction should be consulted before the installation is made. (In Canada, refer to the la

Consideration also must be given to service accessibility. The heater, when installed in aircraft hangars and public garages, must be installed in accordance with ANSI/NFPA 409-latest edition (Standard for Aircraft Hangars), ANSI/NFPA 88a-latest edition (Standard for Parking Structures), and ANSI/NFPA 88b-latest edition (Standard for Repair Garages) with the following clearances: a. At least 10 feet above the upper surfaces of wings or engine enclosures of the highest aircraft that may be housed

System 70Ft. System PTS Body Packages – Alumi-Therm/Aluminized 40 Ft. Pkg 44137090 20 Ft. Pkg 44135030 Part # Each Body Package Includes: Qty. Qty. 42912169 10 Ft. Tube with 6 Hole Flange (Alumi-Therm) 1 - 41932100 10 Ft. Tube less Flanges (Aluminized) 3 2 43319100 Reflector, 9’ 11.” 4 2 30462980 Tube Coupling 3 1 43318000 Tube Hanger/Support Bracket, 13” 4 2 43980010 Wire Hanger 4 2 40 Ft. Pkg 44137090 30 Ft. Pkg 44136050 Qty. Qty. 1 - 3 3 4 3 3 3 4 3 4 3 Body Fastener Kit (included in body pac

40 19.0) Sequence of Operation .......................................................................................................... 40 20.0) Burner Component Location ................................................................................................. 41 21.0) Cleaning And Annual Maintenance...................................................................................... 42 22.0) Troubleshooting Guide .......................................................................

Angle PTS/PTU 40/25 40,000 25,000 #44140061 #32 (0.116) #49 (0.073) 10 ft. 9 ft. 4 PTS/PTU 50/30 50,000 30,000 #44140064 3.5mm (0.138) 46 (0.081) 11 ft. 10 ft. 5 PTS/PTU 75/50 75,000 50,000 #44140063 #21 (0.159) 2.5mm (0.098) 13 ft. 12 ft. 5 PTS/PTU 100/65 100,000 65,000 #44140062 #12 (0..189)) #32 (0.116) 14 ft. 13 ft. 3 PTS/PTU 125/80 125,000 80,000 #44140066 #4 (0..209) #30 (0.129) 14 ft. 13 ft. 7 PTS/PTU 150/100 150,000 100,000 #44140067 “A” (0.234) #27 (0.144) 15 ft. 14 ft. 4 PTS/PTU 175/11

Slide the reflectors on the tube support/hanger brackets and through the wire hangers. 2. The tube at the coupling joints must be covered. Slide the reflectors together and provide an overlap of two (2”) inches for the first reflector overlap after the control unit. All remaining reflector overlaps will be approximately one (1”) inch. This will allow for the natural expansion and contraction of the heater when in operation. Note: The heaters can expand and contract up to 1-3/4” of an inch. 3. Se