See our catalog or website for more details. • On some 351-W Ford engines there may be casting flash on the front cover which will interfere with proper seating of your new fuel pump. File this area flat for proper gasket seating. • When installing fittings, we recommend a liquid teflon thread sealant be used. This will help prevent the fitting from galling and ensure a proper seal. DO NOT use teflon tape. DO NOT over tighten the fitting as this can crack the housing and void the warranty. WARNI

Most installations can be accomplished with common tools and procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation, it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical Hotline at: 1-800-416-8628, 7:00 am - 5:00 pm, Monday through Friday, Pacific Standard Time. IMPORTANT NOTE: Proper installation is the responsibility of the

Don’t shut the hood without checking clearance first! CRANKCASE VENTILATION: Note: Some air cleaner kits include the crankcase ventilation adapter, that mounts to the lower side of the air cleaner per the recess seen in Figure #2 (Crankcase ventilation adapter #1205). Other kits may not be applicable. 1. If you wish to use the crankcase ventilation hose fitting, drill two ." bolt holes (A) in the recessed area at the rear of the air cleaner base, then drill a few ." holes (B) in the larger reces

Si tiene preguntas o problemas, no dude en comunicarse con la linea de asistencia tecnica al telefono: (800) 416-8628, lunes a viernes de 7:00 a.m. a 5:00 p.m., hora del Pacifico o envienos correo electronico a: edelbrock@edelbrock.com. DESCRIPCION: Ensamblajes de depuracion de aire Edelbrock - Debido a las multiples aplicaciones que tienen los filtros de aire Edelbrock, podria ser necesario realizar algunas modificaciones. INSTRUCCIONES DE INSTALACION CONOS DE SEPARACION DEL CAPO 1. Instale una

1. If you wish to use the crankcase ventilation hose fitting, drill two ." bolt holes (A) in the recessed area at the rear of the air cleaner base, then drill a few ." holes (B) in the larger recess window to allow the fitting to breath (See Figure #2). Bolt the fitting to the base with the ." nuts, bolts, and washers. Be sure to de-burr drilled holes. 2. Check for clearance between linkage and ventilation hose and rotate base as necessary. MAINTENANCE: Some air cleaner assemblies have a pre-oil

If you have any questions or problems, do not hesitate to contact our Technical Hotline at: (800) 416-8628 from 7:00 am to 5:00 pm, Monday through Friday, Pacific Standard Time or e-mail us at: edelbrock@edelbrock.com. DESCRIPTION: Edelbrock Air Cleaner Assemblies - Due to the many different applications of the Edelbrock air filters, some modifications maybe required. INSTALLATION INSTRUCTIONS: 1. Install suitable air horn gasket and carburetor stud (not supplied) on carburetor(s) and place air

DESCRIPTION: Edelbrock Air Cleaner Assemblies - Due to the many different applications of the Edelbrock air filters, some modifications maybe required. INSTALLATION INSTRUCTIONS: 1. Install suitable air horn gasket and carburetor stud (not supplied) on carburetor(s) and place air cleaner base over carburetor. 2. For single carb models with dual carb tops, thread the special bracket on the carb stud until the two studs protrude through the top of the air cleaner by about 1/2". Bracket must be pos

DESCRIPTION: Edelbrock Air Cleaner Assemblies - Due to the many different applications of the Edelbrock air filters, some modifications maybe required. INSTALLATION INSTRUCTIONS: 1. Install suitable air horn gasket and carburetor stud (not supplied) on carburetor(s) and place air cleaner base over carburetor. 2. For single carb models with dual carb tops, thread the special bracket on the carb stud until the two studs protrude through the top of the air cleaner by about 1/2". Bracket must be pos

If you have any questions or problems, do not hesitate to contact our Technical Hotline at: (310) 782-2900. • DESCRIPTION This Edelbrock aluminum water pump is a reverse rotation heavy duty water pump for both street and racing applications. It is externally the same as original equipment pumps designed for the applications listed below, but MUST BE USED WITH REVERSE ROTATION SERPENTINE BELT PULLEYS. This pump is ideal for street rods with aftermarket serpentine belt pulleys. It offers weight

Polished Aluminum Water Pump #8892 fits the same applications as #8882. • ACCESSORIES Use #8830 Spacer Kit for short style pumps to clear competition camshaft gear drives and belt drives. Kit includes 1/2" thick water pump and crank pulley spacers. • INSTALLATION Installation is the same as for original equipment water pumps, except that aftermarket reverse rotation serpentine belt pulleys MUST be used. Consult service manual for specific procedures, if necessary. CAUTION: Be sure that fan b