Curves of all other settings fall between the curves shown. A. For CC/AC Mode B. For CC/DC Mode 0 0 50 100 150 200 250 300 350 400 10 20 30 40 50 60 70 80 AC VOLTS AC AMPERES A B C RANGES A = 85.225 B = 70.150 C = 50.100 0 10 20 30 40 50 60 70 80 DC VOLTS 0 50 100 150 200 250 300 350 400 DC AMPERES A C B RANGES A = 85.225 B = 70.150 C = 50.100 4-8. Generator Power Curve 240 425-A The generator power curve shows the generator power in amperes available at the receptacles. A complete Parts List i
Engine must be cold and on a level surface. Unit is shipped with 10W30 engine oil. Engine stops if oil level gets too low. 1 Fuel Valve Open valve. Close fuel valve before moving unit or carburetor may flood and make starting difficult. Fuel Add fresh fuel before starting engine the first time . Fill fuel tank up to 1/2 in. (13 mm) from top to allow room for expansion. Check fuel level on a cold engine before use each day. Oil After fueling, check oil with unit on level surface. If oil reservoi
STICK WELDING (SMAW) GUIDELINES 12-1. Stick Welding Procedure stick2007.04 . ST-151 5931WorkpieceMakesure workpiece is clean be- forewelding. 2Work Clamp3ElectrodeA small diameter electrode requireslesscurrent than a large one. Fol- lowelectrode manufacturer’sinstructionswhen setting weld am- perage(see Section 12-2). 4Insulated Electrode Holder5Electrode Holder Position6Arc LengthArc length is the distance from theelectrodetothe workpiece. A shortarc with correct amperage will givea sharp, crac
ALLGEMEIN ---------------------------------------- Dateioptionen: Kompatibilitat: PDF 1.4 Fur schnelle Web-Anzeige optimieren: Ja Piktogramme einbetten: Ja Seiten automatisch drehen: Zusammen pro Datei Seiten von: 1 Seiten bis: Alle Seiten Bund: Links Auflosung: [ 600 600 ] dpi Papierformat: [ 652 624 ] Punkt KOMPRIMIERUNG ---------------------------------------- Farbbilder: Downsampling: Ja Berechnungsmethode: Bikubische Neuberechnung Downsample-Auflosung: 600 dpi Downsampling fur Bilder uber:
Pour les moteurs diesel : Les gaz d’echappement des moteurs diesel et certains deleurs composants sont reconnus par l’Etat de Californie comme provoquant des cancers et des malformations congenitales ou autres problemes de procreation. 2-7. Principales normes de securite Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (telephone : 1-877-413-5184, site Internet : RecommendedSafe Practices for the Preparation for Welding and Cutting of Contain
7-1. Standard Receptacles If unit does not have GFCI receptacles, use GFCI- protected extension cord. 1 120/240 V 50 A AC Receptacle RC1 RC1 supplies 60 Hz single-phase power at weld/power speed. Maximum output is 10 kVA/kW. 2 120 V 20 A AC Duplex Receptacle RC2 3 120 V 20 A AC Duplex Receptacle RC3 RC2 and RC3 supply 60 Hz single- phase power at weld/power speed. Maximum output from RC2 or RC3 is 2.4 kVA/kW. 4 Supplementary Protector CB1 CB1 protects the ac receptacles from overload. If CB1 ope
Check oil level (see Section 4-2). Engine will not start if oil pressure is too low. Reset circuit breaker CB10 (see Section 7-8). Check coolant level and fan belt (see Section 4-2 and engine manual). Engine will not start if engine temperature is too high. Check and refill crankcase with proper viscosity oil for operating temperature, if necessary (see engine manual). Have Factory Authorized Service Agent check low oil pressure switch S2 and engine coolant temperature switch S3. Engine does not
. . . . . . . . . . . . 1 .. 64 . . . . . . . . . . . . . . . . . . . . . . . LEVER, trip shutdown (included w/engine – see engine parts list) . . . . . . . 1 .. 65 . . . . . . . . . . . . . . . . . . . . . . . SPRING (included w/engine – see engine parts list). . . . . . . . . . . . . . . . . . . 1 .. 66 . . . . . . . . . . . . 181634 . . ENGINE, dsl electric (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .. 67 . . . . . . . . . . . . 087 371 . . . . ROD, sh
Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, norme NFPA 51B, de la National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269.9101 (telephone : (617) 770.3000, site Web : et OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and Part 1926, Subpart J, de l’U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 152
B. Drive rolls can injure fingers. C. Welding wire and drive parts are at welding voltage during operation – keep hands and metal objects clear. 1 Electric shock can kill. 1.1 Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves. 1.2 Protect yourself from electric shock by insulating yourself from work and ground. 1.3 Disconnect input plug or power before working on machine. 2 Breathing welding fumes can be hazardous to your health. 2.1 Keep your h