This manual is devoted to increasing your safety and enjoyment of your Hobie Cat. We ask that you read it all thoroughly and TRY OUR WAY FIRST! Please pay particular attention to the Safety section and the Maintenance, Mooring, and Trailering sections. It would also be a good practice to review these on a periodic basis. DANGER!! Watch for overhead wires whenever you are sailing, launching, or trailering with the mast up. The mast sticks up there a long way and shock or death could result if it

Locate the left and right rudder assemblies. The left one has a red dot and the right one a green dot. The tiller arms should have a slight bow towards the centerline of the boat. INSTALLING THE SAIL BATTENS Unfold the sail and lay it out on the trampoline. There will be a small bundle of thin lines tied to the top of the sail. These are the batten tension lines. Tie the batten tension lines to one of the small grommets at the end of each batten pocket as diagramed in figure 28 (one to each batt

1 Mast Assembly 1-1 Spreader Arm 1-2 Spreader Root 1-3 Clevis Pin 3/16" x 11/16" 1-4 Slide 1-5 Clevis Pin 3/16" x 13/16" 1-6 Brace 1-7 Clevis Pin 3/16" x 9/16" 1-8 Cotter Pin 1-9 Mast Rotation Control Yoke 1-10 Block 1-11 Shackle 1-12 Bolt 4-1/8" Lg. 1-13 Diamond Wire 1-14 Mast Base Assembly 1-15 Nut Nylock 1-16 Diamond Wire Tang 1-17 Mast Tang 1-18 Mast Extrusion 1-19 Clevis Pin 3/16" x 1/2" 1-20 Cotter Pin 20 Illustration No. 2 Jib Halyard Assembly 2-1 Jib Block Housing 2-2 Jib Halyard Wire 2-

Thanks for joining us. By purchasing the Holder@ 12, you are treating yourself to the ultimate in sailing enjoyment. Even if you have long experience with sailboats, please read this manual thoroughly. It will give you easy, accurate instructions on assembling your new boat. We suggest reading through the manual completely before you begin assembly. Pay special attention to the boat and parts descriptions shown on the following pages. If you are new to sailing, this manual will not teach you how

We offer this manual as a guide to increased safety and enjoyment of your new boat. The purpose of this publication is to provide easy, simple and accurate instructions on how to get your Hobie 21 SC ready for the water. Please read them carefully and familiarize yourself with the boat and all of the parts spread before you. Whether you are a new sailor or a veteran of many years, we recommend that you read this thoroughly before your first sail and TRY IT OUR WAY FIRST! If you are new to sailin

Follow these simple instructions and you’ll be out and sailing in minutes. K A t t Î Step 1: Connect mast sections together. Thinner diameter section is mast top. Step 2: Slide the mast into the sail. X Step 3: Insert batten into the narrow sleeve at the top of the sail. Mainsheet. Step 4: Tie in the batten (Note: Be sure that when tying, the batten is pushed snug into the sail. Feed the line through the hold in the batten cap. Next, feed the line through ring on the opposite side o

This owner’s manual is designed to help you get maximum enjoyment from your new Hobie kayak. But more important, it is designed to help you use it safely. The content of this manual covers all inflatable Mirage kayaks. 1 About the Design of your Kayak Hobie Mirage i14t w/ Sail Sit-on-top Cockpit Hobie Mirage kayaks are open-top cockpit designs. This allows the kayaker to enter and exit the kayak easily from the shore, dock or water. Scupper hole(s) make the kayak self-bailing. The design also el

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Re-orient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an .outlet on a cir

17 . 1 pair of universal pliers LIST OF PARTS Hulls (2) Front crossbar Rear crossbar Mast Boom Trampoline Part bag (wires) Rigging bag Ropes bag Rudder assemblies (2) Tiller crossbar Tiller extension Mainsail + battens (7) Jib Trampoline lacing rod Daggerboards (2) It is advisable to be at least 2 people to assemble the Hobie Tiger . CAUTION - DANGER ALUMINIUM MAST - STAY AWAY OF ELECTRICAL WIRES 2 List of parts 1 2 4 5 6 9 ROPES : All ropes are labelled with ref. number and name. Please check c