Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. Homeowner’s Installation and Operating Manual INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. 20012322 1/08 Rev. 3 DVB4136 Direct Vent Gas Fireplace PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING AP

Wait 60 Seconds And Try Again. • For Spark At Electrode While Depressing Piezo NO 1/8" Gap To Pilot Hood Needed. • All Wiring Connections • Replace Piezo Ignitor • For Air In The Lines • Thermopile Needs A Min. 325m V. Adjust Pilot Flame Height. NO • All Wiring Connections • Replace Thermopile • Thermocouple Needs A Min. Of 14m V • Valve Is Turned On • Wall Switch Is Not Turned On. Watch For Grounded Wires! • Thermopile Needs A Min. 325m V. • Plugged Burner Orifice • Defective Valve. Turn to Pil

This appliance may be fitted with a Synetek ignition EB1 JUNCTION BOX 11/18/97 module. Installation of the remote on/off starter switch or wall thermostat on electronic ignition units. 1. Thread the wiring through the holes on the side panels of the appliance. Take care not to cut the wire or insulation on metal edges. Route the wire to a conveniently located receptacle box. 2. Attach the wire to the ON/OFF switch and install the switch into the receptacle box. 3. Connect the white wire from the

WHAT TO DO IF YOU SMELL GAS: • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from your neighbor.s phone. Follow the gas suppliers instructions. • If you cannot reach your gas supplier call the fire department. WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. PLEASE READ THIS MANUAL BEFORE I

7. SIT top Convertible Pilot Gently lift off the pilot hood from the pilot. (Do not remove the spring clip holding the hood in place). Usinga 5/32” Allen key, unscrew the exposed orifice. Insert the new orifice supplied in the kit, do not over tighten the orifice. Replace the pilot hood ensuring the indextab aligns with the notch on the hood. 8. PSE Pilot Using a suitable wrench on the hexagonal body unscrew the pilot hood assembly from the pilot, donot twist the hood itself. Remove the orifice

For USA Installations follow local codes and/or the current National Fuel Gas Code. ANSI Z223.1/NFPA 54. In the Commonwealth of Massachusetts, all gas fitting and installation of this heater shall only be done by alicensed gas fitter or licensed plumber. FOR SAFE INSTALLATION AND OPERATION PLEASE NOTE THE FOLLOWING: 1. This fireplace gives off high temperatures and should be located out of high traffic areas and away from furnitureand draperies. 2. Children and adults should be alerted to the ha

5. Apply high temperature sealant caulking (supplied) around the 4” and 7” snorkel collars. 6. Slide into the vent pipe and secure to the wall. 7. Level the soil to maintain a 4” (102 mm) clearancebelow snorkel. (Fig. 31) 10007317 17 LDVR Series Direct Vent Gas Fireplace 24" (610mm) Minimum* Zero Clearance Sleeve (if required) Firestop 7” Pipe 7TDVSNORK (Snorkel) 4” (102mm) Clearance Min. Window Well Gravel Drain Foundation Wall BG400 Fig. 31 Below grade installation. *A minimum of 24” (608mm) v

For elevations above 4,500 feet (1,370 m) in USA, installations must be in accordance with the current ANSI Z223.1/NFPA 54 and/or local codes having jurisdiction. In Canada, please consult provincial and/or local authorities having jurisdiction for installations above 4,500 feet (1,370 m). Gas Line Installation When purging the gas lines, the window frame assembly must be removed. The gas pipeline can be brought in through the vent end of the fireplace as well as the bottom. Knockouts (to allow

Of 14mv • Valve Is Turned On • Wall Switch Is Not Turned On. Watch For Grounded Wires! • Thermopile Needs A Min. 325mv. • Plugged Burner Orifice • Defective Valve. Turn To Pilot, Meter Should Read Greater Than 100mv. If Not, Replace. 32 10006326 360DVS Series Direct Vent Fireplaces Fuel Conversion Instructions To convert this appliance from gas type to another, follow these instructions. Before proceeding, turn control knob to “OFF” and turn gas supply OFF. Turn OFF any electricity that may be g

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. 360DVS Series Direct Vent Fireplaces Fireplace Dimensions - 360DVS2 CK G Electrical.. Access Gas Line.. Access J J Rear Vent Configuration H E H IJ B F J K K D A K J Electrical.. Access Gas Li