Bolt cap should be on the opposite side of leg from the hinge. 5. Repeat for other set of legs. 6. Position both sets of legs in the upright position with hinges facing one another. 7. Based on the height of the children to be using the easel, determine whether the upper set or the lower set of holes will be used to mount the 2 boards. 8. Attach the green chalkboard (D) to one side of the legs using 4 of the 1 V2" bolts (H) and bolt caps (I). Made in China Alvin & Company, Inc. Bloomfield,

When attached correctly, bottom of drawer face should be aligned with bottom of drawer 2. Using eight remaining 3/4” screws, attach drawers to pre-drilled holes in underside of 51 1/4” tubes located under dust cover. Put screw through center hole in drawer mounting bracket and screw into pre-drilled hole in tube. PLEASE NOTE: When properly installed, larger shallow drawer will be on left and deeper tool drawer (with lock) will be on right.

DC888 PARTS LIST KEY UTY OF SCRIPTION KF r QT y C( ■ÍH f’ílDM KF Y QT Y □ FSCKIPriON 1 5 GLIDE , 7 9 M9x014x2Or«n 12 1 BACKREST POST ♦ 2 1 BASE MACHINE SCREW Pt>STtC COVER 3 1 BASE COVSR S 1 KN08 FOR IN & OUT 13 i PUSTIC HOLOER 4 1 SEAT POST 9 1 FIAT WASHER 14 1 STEEL PUVTE 5 1 SEAT 10 1 LOCK WASHER Í 15 2 BACKREST SCREW 5 1 MECHANISM 11 1 BACKfEST ! 1« 1 PLASTIC COVER STEP 1. > Insert (1) glides Into (2) base Place (3) base cover on (2) base. Insert (4) sett post Into (2) base. S

Description A 1 Back Support Bracket (Thinner) B 1 Front Support Bracket (Thicker) C 1 Bolt for Tray Support (3/4") D 3 Bolts for Tray Support (1/2") E 4 Nuts F 4 5/8" Mounting Screws 1. The instrument tray is reversible. It can be mounted to the left or right side of your table. 2. Attach tray support brackets (A & B) to the instrument tray using bolts (C & D) and nuts (E). Please note that the thicker bracket (B) attaches to the front of the tray and the thinner bracket (A) attaches t

Lumens Tubes Lumens at per Tube per Box Light Box Surface LB1218 650 1 F15T8 650 LB1620 650 2 F15T8 1300 LB1824 650 2 F15T8 1300 LB2436 1750 3 F30T8 5100 All electrical components are U.L. listed. 4. Remove the hold-down screws and lift off the light diffusers. 5. Remove and replace fluorescent tubes. 6. Return diffusers, glass and Plexiglas panels to their original positions. Re-install aluminum strips and screws. T y Alvin & Company, Inc. Bloomfield, CT Grand Prairie, TX www.a

For your own safety, use gloves when handling glass. Place the glass on top of the Plexiglas sheet and replace the aluminum strips. 2. To operate, depress the on/off switch and hold for one or two seconds until the lights illuminate. Note: Bulbs may loosen during shipping. If bulbs don't illuminate check that they are properly seated in fixture. 3. The Satin-Glow Lightbox is designed to operate on 110V AC, 60 cycle. Please do not use any other power source. 4. Removal of the back panel or tam

Always use direct replacement lamps in order to prevent overheating. 2. Disconnect the power cord. 3. Remove the screws and aluminum strips from the top surface of the lightbox. Carefully remove glass and Plexiglas panels. Degrees of Illumination MODEL No. Lumens Tubes Lumens at per Tube per Box Light Box Surface LB1218 650 1 F15T8 650 LB1620 650 2 F15T8 1300 LB1824 650 2 F15T8 1300 LB2436 1750 3 F30T8 5100 All electrical components are U.L. listed. 4. Remove the hold-down scr