AMERIPHONE Inc., 12082 Western Ave., Garden Grove, CA 92841 (800) 874-3005, (714) 897-0808 M03900 CL-40 © AMERIPHONE CL-40 5270-0101 .44/02 Contents Contents Safety Instructions...........................................................................................2 HANDSET Controls-Location and Function............................................... .5 BASE UNIT Controls-Location and Function.............................................. 7 Getting Started.....................................

On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. A plug and jack used to connect this HA30 / HA40 to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug, RJ11 USOC, is provided with this product. It is designed to be connec

IMPORTANT: Always disconnect HA 30/40 from the telephone before replacing the battery! 2 Installation: 1. Unplug the handset cord from your telephone base. Insert this plug into the jack at the front of the Handset Amplifier. 2. Connect the Handset Amplifier to your telephone base as shown. 3. Pick up the handset. If there is a dial tone, you have installed the Handset Amplifier correctly. Volume Control Adjust the volume to the most comfortable listening level by moving the volume control slide

• Setup special features Installing the Backup Batteries To add extra brightness to the Dialogue XL-25s’s ring flasher when you receive calls, install one 9 Volt alkaline battery (not included). Note: For your safety always unplug the phone line before you install or replace the backup battery. 4 Figure 3 To install new battery: 1. Slide open the battery compart-ment cover on the bottom of the telephone, (Figure 3). 2. Install one fresh 9-volt battery. The battery indicator on the base unit will

SAVE THESE INSTRUCTIONS Contents Introducing the Dialogue XL-25s ............................................................2 Warranty Service ......................................................................................2 Sales Receipt ............................................................................................2 Help from Ameriphone................................................................................2 Features .................................................

Help from Ameriphone For help with using your DIALOGUE JB-20 , call our Customer Relations department at 800-894-3005. Please make sure your DIALOGUE JB-20 package includes the items shown in Figure 1. Base Unit CHAPTER 3 FEATURES IDENTIFICATION RINGER TONE selector HOLD button Ringer control switch (volume) Audio Output jack Tone / Pulse switch Emergency buttons Braille characters Raised letters for easy identification REDIAL button MEMORY button HANDSET VOL control (volume) FLASH button PROG b

3. Press the MEMORY b button and then the desired MEMORY button (Figure 24) to store this number as the second phone number in the same memory location. Making and Answering VCO Calls A person with hearing loss who uses their voice can use voice carry over (VCO) through the toll-free local relay service to communicate with a hearing person. In a VCO (voice carry over) call, the hard of hearing person speaks directly to the other party. The Communications Assistant (CA) relays the response from t

When AMPLIFY is on, the AMPLIFY indicator comes on. P E0 # HOLD PROG TONE LO HI FLASH REDIAL VOL AMPLIFY * Figure 8 - AMPLIFY Button and Indicator 2. Adjust the volume in the ear piece by moving the VOL slide control in Figure 9. With AMPLIFY on, incoming volume will be up to 48dB louder. Caution: Repeated incremental exposure to amplification levels greater than 18 dB may be harmful to individuals without hearing disabilities. Therefore, do not remove the warning label attached to the back of t

When the desired memory location is lit, press the SCAN button again to select. 4. The DIALOGUE RC automatically dials the number selected. 5. Press the ON/OFF Figure 16 button to hang up. Dialing using the Remote Transmitter A. With Scan function on: 1. Press the Remote Transmitter to begin scanning. FLASH/PAUSE REDIAL MUTE ON/OFFHEADSET MIC Figure 17 2. When the desired memory location is lit, press the Remote Transmitter. The DIALOGUE RC automatically dials the number selected. 3. Press the R

to turn on phone. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 • • Voice Activated answering is off, (RC-200 only). Ring volume set to Hi. Unanswered call indicator is on. ”0“ (operator) is programmed into Voice Mail indicator is off, (RC-200). Remote Flash switch is off, the first memory location of M1. Press 0 on the keypad to Press SCAN button. turn it off; or Press 1 key on the keypad to turn it on. 32 Press 0 key to turn it off; or Press SCAN button. Press 1-9 keys to turn it on. See Page 5 for rate selecti