Step 2: One way to do this is to turn the low "low E" string fine tuner screw all the way up, then turn the "D" string fine tuner screw all the way down. Now, position the "A" string fine tuner screw half way between the "E" and the "D" fine tuner screw positions. Step 3: Now, leaving the "A" string fine tuner where you set it, reposition all the of the other fine tuner screws to match the height of the "A" string fine tuner screw. You should now have all of the fine tuner screws set to the midd

By the way, the SpeedLoader Tremolo will retrofit an Original Floyd quite easily. The first thing you'll want to do is check to see if the top surface of the base plate of the bridge is sitting parallel to the top surface of the guitar. If the base plate appears to be tilted forward away from the top surface of the guitar or tilted back closer to the top of the guitar, then an adjustment should be made. Step 1: To level the base plate, first take the spring cover plate off the back of the guitar

Step 3: If this part is missing stop right here and get one installed by a qualified guitar repairman.You can get this part from Depending on the guitar you purchased, the tremolo stop may or may not be engaged with the spring block. We will assume it is not engaged and show you how to engage it. Take the 3mm Allen wrench and turn the setscrew until it touches the spring block. Step 4: Now, tighten the springs with the spring claw screws so the spring block is pulled tightly against the setscrew

Controls Bronze Series guitars The Bronze Series has 3 controls to adjust the sound of the guitar. • The first knob (closest to the bridge pickup) is the Master Volume. It controls the loudness of both pickups. • The next control is the 3-way Pickup Selector. It is used to switch the two pickups on or off. Switching the selector up will engage the neck pickup. The middle position engages both pickups, and switching it down will engage the bridge pickup. • The final control is the Master Tone con

Step 3: If this part is missing stop right here and get one installed by a qualified guitar repairman.You can get this part from Depending on the guitar you purchased, the tremolo stop may or may not be engaged with the spring block. We will assume it is not engaged and show you how to engage it. Take the 3mm Allen wrench and turn the setscrew until it touches the spring block. Step 4: Now, tighten the springs with the spring claw screws so the spring block is pulled tightly against the setscrew

Occasionally an instrument's neck may need adjustment as a result of string tension or climactic changes.The curvature of the neck should be slightly concave. The amount depends on the player’s personal taste. Truss rod adjustment should only be performed by a B.C. Rich Authorized Service Center. Over adjustment can cause permanent damage that will not be cover by the warranty. 5 REMOVING SPEEDLOADER GUITAR STRINGS *For use with SpeedLoader™ bridges only. Please note: SpeedLoader strings are off

Platinum, Platinum Pro, Acrylic, NJ and Classic Series guitars These guitars have 4 output controls: • The first knob (closest to the bridge pickup) is the Volume Control for the bridge pickup. It controls the loudness of this pickup. • The next control is the 3-way Pickup Selector. It is used to switch the two pickups on or off. Switching the selector up will engage the neck pickup. The middle position engages both pickups, and switching it down will engage the bridge pickup. • The next control

The safety catch is there to prevent the string from accidentally releasing while playing or changing strings. 7 LOADING SPEEDLOADER STRINGS Step 1: To put on the new string simply slide one of the bullets into the nut, then place the other bullet into the appropriate saddle and push down on the back on the saddle until you hear, or feel, a snap. Step 2: This sound is the spring-loaded sliding latch snapping into place. If you don't hear or feel the snap, push the sliding latch toward the saddle

If only one or two of the fine tuners are out of range you may want to try adjusting them without engaging the tremolo stop. Step 1: The first thing you do to reset the range of all the fine tuners is to position all the fine tuner screws to the middle of their possible movement. Step 2: One way to do this is to turn the low "low E" string fine tuner screw all the way up, then turn the "D" string fine tuner screw all the way down. Now, position the "A" string fine tuner screw half way between th

14 When you do need to change batteries you will get better performance and battery life if you use an alkaline battery.The battery compartment is located on the back of the bass just above the control cavity. It can easily be opened by unscrewing the 2 screws with a Phillips head screwdriver. Changing the battery will not affect your warranty. The controls for both the NJ and Innovator series are as follows: (see photo) • #1 is the Master Volume. It controls the output of both pickups. • #2 is