Do not use outdoors. 2.Position the toaster on a firm, level, heat-resistant surface, close to a power socket and out of the reach of children. 3.The toaster must not be used near or below curtains or other combustible materials and it must be watched, as bread if overcooked can catch fire. 4.The area round the toasting slots will become hot during use.Do nottouch these surfaces. 5.Do not allow anything to enter any of the "empty" slots while toasting,as the central elements are "live"when the l

Always place tli sandwich toward the near end of the plate. 5. Close the upper plate, and lock it with the height control-The heating plates mu be in a closed position before connecting with supplier mains, 6. Insert the plug into a mains socket The red operating lamp is on. 7. Allow green lamp on and off during operation. 8. Depending on the thickness of your sandwich, takes approx.5-S minutes. y. After toasting, open the upper plate,and lock it with the height control.Remov your sandwich

This reduces the waiting times (the iron takes less time to heat up than to cool down) and eliminates the risk of scorching the fabric. AUTOMATIC SHUT OFF The automatic shut off device trips after the iron has been left for approx. eight minutes in the upright position or unused for approx. Thirty seconds in the horizontal position. The light comes on to indicate that shut off has tripped. As soon as you move the iron, the device turns off and the iron starts working again. STEAM IRONING Filling

TABLE OF CONTENTS IMPORTANTSAFETYINSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . .3 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 CYCLE TIMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 COST OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . .5 SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 CHANGING THE FILTER . . . . .

INSIDE: Attach and secure the flex liners to the vent connection assembly using the same procedure as before, ensuring that the marked exhaust liner is attached to the exhaust collar. FIGURE 3 FIGURE 4 VENT CONNECTOR EXTENSION RESTRICTOR PLATE STUDS FIGURE5a-b 5. Reaching in through the insert, manoeuvre the vent connection assembly through the openings in the firebox top, taking care not to damage the gasket. In case of a low ceiling fireplace, the extension should be removed and reinstalled af

Immediately call a qualified service technician to inspect the fireplace insert and to replace any part of the control system and any gas control which has been under water. • Do not operate the fireplace insert with the glass door opened, cracked or broken. Replacement of the glass should be done by a licensed or qualified service person. • Do not strike or slam shut the fireplace insert glass door. • This fireplace uses and requires a fast acting thermocouple. Replace only with a fast acting t

FIGURE 9a-c The fireplace requires a minimum enclosure height of 39”. For temperature requirements, the enclosure space around and above the fireplace must be left unobstructed. W415-0298 / K / 12.06.07 FINISHING HOODGRATE AND LOG INSTALLATION FINISHING HOODGRATE AND LOG INSTALLATION 1. Remove curtain mesh and rod assembly 2. Remove log carton 3. Remove grate from the lower control area (stored there when shipped) 4. Unscrew the 3 screws in the firebox, set grate in place and secure using the 3

UNVENTED MILLIVOLT SYSTEM INSTALLATION AND OPERATION INSTRUCTIONS FOR UNVENTED GAS FIREPLACE NATURAL GAS MODEL CVF36N PROPANE GAS MODEL CVF36P CERTIFIED FOR UNITED STATES USING ANSI METHODS WARNING: If the information in these instructions is not followed exactly, a fi re or explosion may result causing property damage, personal injury or death. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapours and liquids in the vicinity of this or any other appliance. WHAT TO DO IF YOU SM

Para desconectar, agarre el enchufe y remuévalo de la salida. No jale directamente el cable. No use este aparato para otro uso del que no ha sido construido. 1 I ■0sn papúes! s,i! ивщ jeiflo joj eouendde esn jou oa ' IU pjoo 9Ц} uo ||nd \ou oa 10ЦПО iuojj oaouuoj рив 6n|d dsejß ‘P0UUOOSIP 01 }0|}ПО |BOUP0|0 0Щ pjoo 6n|d ‘0sn 01 oi U0AO 0ABMOJO|IU JO |BUO!ÏU0AUOO в U! jo ‘joujnq ouio0|0 jo ‘sb6 }оц в jbou jo uo 0OB|d pu oa '6 •sooBjjns jol| ipno} jo ‘j0junoo jo 8|qBi p ©6p0 J0AO 6ubl| pjoo

Slip the liner a minimum of 2" over the inner sleeve of the air terminal and secure with 3 #8 screws. Apply a heavy bead of the high temperature sealant. 3. Using the 8" diameter flexible aluminum liner, slide over the outer combustion air sleeve of the air terminal and secure with 3 #8 screws. Seal as before. The air terminal mounting plate may be recessed into the exterior wall or siding by 1.", the depth of the return flange. 5. Apply a heavy bead of the high temperature sealant, supplied wit