BLUE - Night Dimming: connect to the head light switch. BLACK - connect to a main ground location Mounting: The gauge requires an oval hole 1-7/16” high x 3-1/16” wide. It should be inserted into the opening from the front and the 2 L-clamps will be installed from the back. Tighten a nut on each of the L-clamps so that the gauge is secure. Gauge depth to the back of the case is 1”. Gauge depth including the mounting studs is 1-7/8”. Operation: The gauge needs the red, orange, and black wires con

Top “set” button advances hours, bottom “set” button advances minutes. Each time that you make a change to either the hours or minutes, the seconds are reset to zero. Adjusting the accuracy: The clock is accurate to +/-2 minutes a month as it is sent. It can be tuned for better accuracy if desired. Press and hold both of the set buttons for several seconds. The clock will display “C 0”. The “C” indicates that it is in the calibration mode and the second number is the current calibration value. T

3Speeds are approximate and may vary slightly depending on application Wiring to a door lock motor. Dakota Digital RLY-2 relay pack shown. To PAC-3500Lock output. FUSED 12V POWERTo PAC-3500Unlock output. The wires between the switch and the motor will need to be cut, and the relay pack wired in between as shown. Fused 12V power. MOTORMOTORSWITCHPURPLEGREENBROWNWHITEBLUERELAYREDsmall wireGREENPACKBLUEsmall wireDUAL+12v on lock+12v on lock Indicator LEDs The green LED will turn on when the auto-lo

incorporates the reliability and quality of our standard gauges, along with several unique features and easy mounting. These features include: • Quartz accuracy. • Night dimming feature. • Very low standby power to prevent battery drain. • High Visibility VFD display for sunlight readability. The Odyssey series clock displays the current time in 12 hour format. The high brightness display matches our other Odyssey and STR series gauges and has the same night brightness dimming capability. Operat

If the gasket is hard or brittle it should be replaced. 4. Now is a good time to clean or replace the lenses and housings if necessary. If the lenses are in poor condition a replacement set is recommended. MAN#650217 5. Insert the LED assembly bulb base into the tail light housing socket. 6. Place the new LED assembly into the housing so that the aluminum mounting bracket sits into the groove for the lens gasket. 7. Replace the lens gasket. The gasket will sit on top of the aluminum mountin

(A second relay, sold separately, is required for two speed or dual fan operation). The controller monitors the engine temperature using a dedicated sender, or a gauge and its sender. When the engine temperature goes above a user adjustable set point, the fan is turned on with a relay. When the engine has cooled below a user selectable off temperature, the fan is shut off. Separate on and off temperatures can be set for the high and low fan outputs. The controller will also run the fan when the

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Insert the supplied rubber grommet into the hole where the original light socket was located. This will protect the wires from rubbing on the metal edge. 6. Make sure the stock lens gasket is removed from the housing and place the supplied drill template into the

2. Remove the light bulb 3. Push and twist to remove the plastic wire socket from the back side of the housing. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the lock nut and flat plastic back plate from the back of the new LED assembly. 6. Make sure that one wire is still going through each hole in the aluminum spacer. Insert the new LED assembly through the hole where the original bulb and connector were located. Use caution

UTV-1200 Multi Gauge for 2008 Yamaha Rhino Operation menu Left switch functions Pressing the left switch during normal gauge operation will move through the below commonly viewed functions for convenience. 00000.0 Odometer 12:00A Clock (hold left switch to set) Setting clock: Left switch press moves between hours and minutes Right switch press changes current value Hold left switch again to exit clock set mode H 0.0 Hourmeter Right switch functions Pressing the right function switch during norma

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. 4. Now is a good time to clean or replace the lens and housing if necessary. 5. Remove the two screws and aluminum plate from the back of the new LED assembly. 6.Insert the new LED assembly through the hole where the original bulb and connector were. Be careful when feeding the wires throughto avoid damaging insulation. 7.Feed the wires through the larger hole in themoun