Log:

Desa GA2100A

Downloads : 0 Arquivo Tamanho: 37 kb    Fabricante : Desa  
Categoria : Fans

Contact a qualified service person to do this. All local codes must be followed. ! WARNING Fan accessory must be grounded. Fan comes with a three-prong, grounding plug as shown in Figure 1. The plug is your protection against electrical shock. Plug it into a standard, three-hole, grounded, outlet. If cord needs replacing, use only a cord with a three-prong, grounding plug. Grounding Plug Grounded Outlet Figure 1 - Grounding Plug Attaching Fan Accessory 1. Knock out center panel at four tabs with

Desa KH 1117

Downloads : 2 Arquivo Tamanho: 69 kb    Fabricante : Desa  
Categoria : Lareiras

you can control the room temperature with the thermostat .. . Turn the Thermostat . to the "max“ position. As soon as the desire room temperature is reached... . Turn the Thermostat . back till you hear an audible click. The in-built thermostat now ensures a constant room temperature. Flame regulator With the Flame regulator . you can regulate the flame to any size. . Turn the Flame regulator . in the clock-wise direction until the desired flame size is obtained. Replacing the bulbs Danger of l

Desa 34310

Downloads : 0 Arquivo Tamanho: 119 kb    Fabricante : Desa  
Categoria : Pistola de pregos

Trigger This tool has an easy squeeze trigger. The trigger is located underneath the hand grip. Each squeeze of the trigger fires one staple. Make sure your finger is not on the trigger when connecting or loading the tool. ON/OFF Trigger Lock This tool is equipped with a sliding ON/OFF trigger lock. The trigger lock is located at the front of the hand grip, just above the trigger. This safety feature helps prevent accidental firing. Make sure the trigger lock reads OFF when plugging in or loadin

Desa 102865-01

Downloads : 4 Arquivo Tamanho: 146 kb    Fabricante : Desa  
Categoria : Placa

You can also visit DESA’s technical service web site at 3. Align shim under adjusting plate as shown in Figure 1. 4. Slide one end of adjusting plate/shim in slot on mitered edge of top trim (see Figure 1). 5. Slide other end of adjusting plate/shim in slot on mitered edge of side trim (see Figure 1). 6. While firmly holding edges of trim together, tighten both screws on the adjusting plate using a slotted screwdriver. 7. Repeat steps 2 through 6 for other side. 8. Place the assembled trim

Desa 3LY41/8540

Downloads : 0 Arquivo Tamanho: 151 kb    Fabricante : Desa  
Categoria : Eléctrico

FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. DESCRIPTION The AirKing Oscillating Ceramic Heater features 2 heat settings and a fan only setting.The heater oscillates 120°and comes with a remote control for convenience. This unit also features a built in timer to allow up to 7.5 hours of operation before automatic shut- down and comes with a 6ft. (1.82m) 16/3 grounded cordset. SPECIFICATIONS Motor ...........

Desa B50H

Downloads : 1 Arquivo Tamanho: 163 kb    Fabricante : Desa  
Categoria : Eléctrico

Remove upper shell (see page 8). 2. Remove filter end cover screws using 5/16" nut-driver. 3. Remove filter end cover and air filters. 4. Remove pump plate screws using 5/16" nut-driver. 5. Remove pump plate. 6. Remove rotor, insert, and blades. 7. Check for debris in pump. If debris is found, blow out with compressed air. 8. Install insert and rotor. 9. Check gap on rotor. Adjust to .003"/.004" if needed (see Figure 13). Note: Rotate rotor one full turn to insure the gap is .003"/.004" at tight

Desa NON-OSCILLATING 9335

Downloads : 0 Arquivo Tamanho: 163 kb    Fabricante : Desa  
Categoria : Eléctrico

SAVE THESE INSTRUCTIONS 4 Rev. A 11/07 1 Rev. A 11/07 5084416 5084416 IMPORTANT INSTRUCTIONS - OPERATING MANUAL IMPORTANT INSTRUCTIONS - OPERATING MANUAL CEILING MOUNT INSTALLATION (Figures 1 and 2) NOTE: Distance mounted from the ceiling can be changed by using a length of 1-1/2” NPT pipe. Simply substitute your pipe for the provided threaded pipe. 1. Locate the Pipe Mounting Flange, securely mount to ceiling structure. Ensure ceiling structure can safely support the installed Fan. 2. Open one

Desa NON-OSCILLATING 9371

Downloads : 5 Arquivo Tamanho: 163 kb    Fabricante : Desa  
Categoria : Eléctrico

One of each is shown in the illustrations below. 1. Install the Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6) 10-32 X 5/16” Hex Screws through the Rear Grill into the Motor. Securely tighten all (6) screws. (Figure 3) 2. Push the Fan Blade onto the Motor Shaft, centering the Hub facing away from the motor, until it stops against the shaft. (Inset A) Align Square Head Bolt with flat of the Motor Shaft. TIGHTEN VERY SECURELY W

Desa NON-OSCILLATING 9370

Downloads : 0 Arquivo Tamanho: 163 kb    Fabricante : Desa  
Categoria : Eléctrico

GRILL AND BLADE ASSEMBLY (Figures 3 and 4) NOTE: The assembly of the blade and grill is identical, regardless if the Fan has an oscillating motor or a non- oscillating motor. One of each is shown in the illustrations below. 1. Install the Rear Grill onto the Motor, lining up the six holes in the grill with the six threaded holes in the Motor. Install (6) 10-32 X 5/16” Hex Screws through the Rear Grill into the Motor. Securely tighten all (6) screws. (Figure 3) 2. Push the Fan Blade onto the Moto

Desa NON-OSCILLATING 9374

Downloads : 9 Arquivo Tamanho: 163 kb    Fabricante : Desa  
Categoria : Eléctrico

com PARTS FOR DISCONTINUED, OBSOLETE AND CERTAIN OTHER PRODUCTS MAY NOT BE AVAILABLE. DUE TO SAFETY REASONS, MANY ELECTRONIC COMPONENTS AND MOST HEATER COMPONENTS ARE NOT AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT. SAVE THESE INSTRUCTIONS 4 Rev. A 11/07 1 Rev. A 11/07 5084416 5084416 IMPORTANT INSTRUCTIONS - OPERATING MANUAL IMPORTANT INSTRUCTIONS - OPERATING MANUAL CEILING MOUNT INSTALLATION (Figures 1 and 2) NOTE: Distance mounted from the ceiling can be changed by using a length o





categorias