See fig.4. REV B. 11.07 6. Raise and center the arch over the fabric and attach the remaining two poles to erect a free standing unit. See fig. 5. 7. Attach the four center clips to the poles. See fig.6 9. Square up the tent and stake down all four corner loops. See fig.8. 10. Tuck the ground skirts under the walls and into the tent. Your Northern Breeze is ready. See fig.9. 8. Attach the bungee cords to the corner hooks. Then attach all remaining clips. See fig.7 & 8. 11. The Northern B

fig.5 fig.4 fig.1 fig.2 fig.3 fig.6 fig.7 • Unpack the tent bag, pole bag and separate all of the components. Unroll and unfold the fabric with the Eureka! label up. Locate the hub fitting attached to the center of the roof. See fig.1. Important: Align the hub arms to match the layout of the fabric. • Make sure the hub and fabric are still aligned. Then, insert the proper corner ring & pin into the bottom pole section. See fig.3. • Assemble all of the shockcorded poles. Check and make sure that

Check and make sure the hub and fabric are aligned. Then, insert the proper corner ring & pin into the bottom pole section. See fig.4. FOR LIFE OUTDOORS. Assembly Instructions for the Breezeway: You can usually assemble this Breezeway alone. However, with first time set-up or with windy conditions, you will need help. Component List: 1 Screen/Body w/ Hub 1 Tent Bag 1 Pole Bag 4 Poles 1 Stake Bag and Stakes 1. Unpack the tent bag, pole bag and separate all of the components Unroll and unfol

Choose a suitable place and unroll and unfold the fabric with the Eureka! label up. • Assemble all of the chain-corded poles and rafters. Check and make sure that each section is fully seated into the next. See fig.2. Important: Locate the hub fitting attached to the center of the tent roof. Align the hub arms to match the layout of the corner pins without twisting the fabric. See fig.1. Fit the Rafters • Slide a rafter section labeled "TOP" onto a hub arm.The spring clip must engage the slot in

Remove the fly and open the tent door. Do not stake down the tent just yet; But in windy conditions, stake down one front corner into wind. NOTE: Do not drop tent bag or pole bag on its end. Do not bounce tent bag on its end to get tent out. These actions may cut the shock cord and/or damage the pole ends. • Assemble all the shock-corded poles. Make sure each pole section has firmly seated into the adjacent section. Try to keep the poles from snapping together as this can damage the rod ends. Th

The guy lines will work together through opposition. See illustrations below: CONDENSATION & VENTING: Through perspiration and breathing, an adult gives off about a pint of water overnight. If it cannot escape, the water vapor condenses to liquid. Most often, water found in the tent is a result of this condensation rather than from the tent leaking. Condensation often forms where the sleeping bag touches the side of the tent, under the sleeping pad, or on coated surfaces such as the door flaps.

Remove the fly. Un-clip the tent from the poles. Pull poles out of the grommets, collapse the poles and stow in the bag. Fold the tent and fly. Lay the fly on the folded tent along with the bag of poles. Roll up all and stow in the carry bag. Optional: Add durability and versatility to your tent with our “Lite-Set” Footprint. It’s made of the same fabric as the tent's floor: complete with web loops, grommets, and side release buckles. The Footprint, in combination with the fly and poles creates

The best way is to pry on the stake itself. Staking in special conditions: • Sand. Use long, broad stakes with plenty of surface area in loose soil. • Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes separately. Their sharp edges can cut fabric and leave rust stains, which might damage your tent. • Snow. Use “dead man” anchors. Tie tent to buried objects (branches, tent bags, or stuff sacks filled with snow; or tie tents to snow shoes, skis, or ski poles, which are stuck i

Leave the canopy folded until the roof rafters are up 2. Locate The Crown Assembly. Lay it on the ground, near the center of where you want the shelter to stand. Spread the arms and orient the crown so that the BLUE tipped arms point to the corners 3. Assemble The Rafters. Each rafter is two sections that are shockcorded together. The roof rafters are either BLUE or RED tipped and the perimeter rafters are GREEN tipped. Fit the centers together, making sure that the detent buttons are fully seat

• With the tent properly staked, drape the fly over the frame, attach its tent connection points and stake down any pull outs. • Do not attempt to remove the stakes by pulling on the tent becket loop, as this could cause the fabric to tear. The best way is to pry on the stake itself. Staking in special conditions: • Sand. Use long, broad stakes with plenty of surface area in loose soil. • Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes separately. Their sharp edges can cu