Always keep the cylinder mower clean and remove grass deposits. Deposits affect the cutting result as well as discharge of grass clippings. Residual dirt and grass is easily removed immediately after mowing. 1. Remove grass deposits with a brush and a cloth. 2. Oil the red cutting mechanism lightly with thin oil (e.g. sprayed oil). 7. Troubleshooting DANGER! Cutting tool can cause injuries! V Wear suitable work gloves when rectifying faults. 10 Fault Possible Cause Rectification Abnormal Noises

C/ Basauri, n. 6 La Florida 28023 Madrid Phone:(+34) 917080500 atencioncliente@gardena.es Sweden GARDENA Norden AB Forsaljningskontor Sverige Box 9003 200 39 Malmo info@gardena.se Switzerland / Schweiz GARDENA (Schweiz) AG Bitziberg 1 8184 Bachenbulach Phone: (+41) 848 800 464 info@gardena.ch Turkey GARDENA / Dost Di. Ticaret Mumessillik A... Sanayi Cad. Adil Sokak No.1 Kartal - Ystanbul Phone: (+90) 2163893939 info@gardena-dost.com.tr Ukraine / Украина ALTSEST JSC 4 Petropavlivska Street Petrop

Feed the hook (A2) attached to the lower handle (A1) halfway through the centre slot of the guide (A3), in the direction indicated by the arrow (A4). 2. Maintaining the hook (A2) in the centre slot of the guide (A3) turn the lower handle (A1) clockwise through 900 to place both legs of the lower handle in position between the hood brackets (A5). as illustrated in Fig A. 3. Fit the lower handle (B1) to the deck with the lower handle pin (B2) as illustrated in Fig B. Fitting the Wheel frame to

Removing broken or worn cutting line. For best results, replace the cutting line when worn to no less than 20 mm from the edge of the cutting head. (Fig F) Using the pip in the centre of the line, pull the line upwards and out of the cutting head. (Fig G) G USE 8 8 Replacing the Cutting Line USE H J K Insert one end of the cutting line into the centre of the cutting head and push until the end of the line comes out at one end of the slot. (Fig. H) Secure the centre piece of the cutting line into

The operator is responsible for following the warning and safety instructions in this manual and on the Hedgetrimmer. Explanation of Symbols on the HT39, HT42, HT42s, HT45s, HT53s Warning. Read the user instructions carefully to make sure you understand all the con- trols and what they do. Switch off! Remove plug from mains before adjusting, cleaning or if cable is entangled or damaged. Keep the cable away from the blade. Do not use in the rain or leave the Hedgetrimmer outdoors while raining. T

IF ANY PARTS ARE MISSING CONTACT:- Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 HT39/HT42 HT42s/HT45s/HT53s instruction manual Switch levers blade cover instruction manual Switch levers blade cover 1 Carton Contents IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Electrolux Outdoor Products Customer Service Department direct Telephone : 01325

Switch off, remove plug from mains and condition; examine electric supply cable for damage or -if the Hedgetrimmer starts to vibrate abnorageing before winding cable for storage. Do mally. Check immediately. Excessive vibranot repair a damaged cable, replace it with a tion can cause injury. new one. Use only Flymo replacement -before passing to another person. cable. Maintenance and storage 12. Always wind cable carefully, avoiding kink- 1. Keep all nuts, bolts and screws secure to be ing. sure

See Fig. F. A slight downward tilt of the cutting blades in the direction of motion gives the best cutting results. Side Cutting When trimming the sides of the hedge, begin at the bottom and cut upwards (See Fig. G), tapering the hedge inward at the top. This shape will expose more of the hedge, resulting in more uniformed growth. F G 5 Caring for your Hedgetrimmer Fault Finding Hints Fails to Operate 1. Is the Power Turned On? 2. Check the fuse in the plug, if blown replace. 3. Fuse continues t

9. Cutting test: Place a strip of paper S in such a way on the lower blade P that it points towards the spindle of the cylinder O. 10. Turn cylinder O carefully. If the lower blade is set correctly P the paper will be cut off as if with scissors. 11. Repeat the cutting test on the other blades O. If the Accu capacity is completely exhausted or if the Accu can no longer be recharged it must be exchanged. New Accus are available directly from GARDENA Service. 1. Press Accu cover C lightly at the f

2. Swing trimmer in and out of the cutting area taking small cuts. F Spool Cap 7 • WARNING Disconnect from the mains electricity supply, before attempting any maintenance or adjustment. Cutting head continues to rotate after the trimmer has been switched off. To remove spool cap 1. Press and hold in the two cap release latches. See fig G. 2. Pull cap away from the cutting head. See fig H. When refitting the spool cap 1. Keep all areas of the cap and spoolholder clean. Failure to do so may preven