(305 mm) long 18 in. (457 mm) long 24 in. (610 mm) long Fits all Graco high pressure spray guns. (Adapters available for other guns) Includes DripLess™ Tip Guard. Order spray tip separately. GUN NOT INCLUDED WARNING Pressure Relief Procedure To reduce the risk of serious bodily injury, including fluid injection, splashing fluid or solvent in the eyes or on the skin, or injury from moving parts or electric shock, follow this procedure whenever you shut off the sprayer, when checking or ser

PART NO. DESCRIPTION QTY 1 180-137 NUT, gun 1 2 180-136 ADAPTER, tip 1 3 166-969 WASHER, tip 2 4 220-222 TIP GUARD 1 5 EXTENSION TUBE 218-244 12 in. for Model 223-390 1 218-245 18 in. for Model 223-391 1 218-246 24 in. for Model 223-392 1 GUN NOT INCLUDED ACCESSORIES Must be purchased separately. SPRAY GUNS Includes Reverse-A-Clean IV DripLess™ Tip Guard and a SwitchTip™ “SILVER” GUN 220-954 5000 psi (350 bar) Max. Working Pressure SwitchTip ™ is size 517. “CONTRACTOR” GUN 220-95

Now clear the tip or hose. -WARNING- Hazard of Using Fluids Containing Halogenated Hydrocarbons Never use 1,1, 1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in this equipment. Such use could result in a serious chemical reaction, with the possibility of explosion, which could cause death, serious bodily injury and/or substantial property damage. Consult your fluid suppliers to ensure that the fluids being used are compatible

READ AND KEEP FOR REFERENCE. INSTRUCTIONS Rev. D Supercedes Rev. C Pressure Roller Equipment 300 psi (21 bar) MAXIMUM WORKING PRESSURE Operate your pump at the lowest pressure needed for sufficient paint supply to your roller Adjustable Extension Roller Kit 218–625 Includes Roller Frame, 18–36 in. Extension Tube, 3/8 in. nap Roller Cover and 45 Gun Adapter Adjustable Extension Tubes 218–775 18–36 in. (0.45–0.9 m) 218–776 3–6 ft (0.9–1.8 m) 218–777 6–12 ft (1.8–3.7 m) *45 Gun Adapter 218–932 1/4

Do not remove any spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings. FIRE AND EXPLOSION HAZARD . If there is any static sparking or you feel an electric shock while using this equipment, stop dispensing immediately. Do not use the equipment until you identify and correct the problem. . Keep the dispensing area free of debris, including solvent, rags, and gasoline. . Electrically disconnect all equipment in the dispensing area. . Extinguis

. Do not stop or deflect leaks with your hand, body, glove or rag. . Tighten all connections before operating the equipment. . Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately. Permanently coupled hoses cannot be repaired; replace the entire hose. . Use only Graco approved hoses. Do not remove any spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings. FIRE AND EXPLOSION HAZARD . If there is any st

For storage, flush the system with Graco Pump Armor or mineral spirits/paint thinner. See Flushing on page 3. WARNING To help prevent injection injuries, follow this procedure whenever you stop painting. psi/MPa/bar 1. Put gun trigger safety in SAFETY ON position. 2. Shut off power to pump. 3. Put pump prime/drain valve (required for pressure relief) in DRAIN position to relieve pressure in system. 4. Put gun trigger safety in SAFETY OFF position, and trigger gun to relieve any pressure in hose.

READ AND KEEP FOR REFERENCE. INSTRUCTIONS Pressure Roller Model 243066, Series A . 20 in. (50 cm) heavy-duty extension . 45 swivel adapter . 9 in. (23 cm) roller frame . 1/2 in. (13 mm) nap roller cover 3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure * This maximum pressure is only possible if the roller frame is * completely plugged. The best operating pressure is the lowest pressure that provides an even paint supply to the roller and typically does not exceed 300 psi (2.1 MPa, 21 ba

See Flushing on page 3. WARNING To help prevent injection injuries, follow this procedure whenever you stop painting. psi/MPa/bar 1. Put gun trigger safety in SAFETY ON position. 2. Shut off power to pump. 3. Put pump prime/drain valve (required for pressure relief) in DRAIN position to relieve pressure in system. 4. Put gun trigger safety in SAFETY OFF position, and trigger gun to relieve any pressure in hose. 5. Put gun trigger safety in SAFETY ON position, and keep pump prime/drain valve in D

1. Shut off the pump or sprayer. 2. Trigger the gun. 3. Open the gun air valve. 4. Disconnect the power source. Grounding To reduce the risk of electric shock, proper electrical grounding is essential. See your separate pump or sprayer instruction manual, and consult your local electrical codes for detailed grounding instructions. Working Pressure To reduce the risk of component rupture and serious bodily injury, never exceed 100 psi (7 bar) AIR OR FLUID WORKING PRESSURE to this gun. Do not exce