• RB709U-NBtwochannelreceiverwithinstructions. • TwosizeAAbatteries. • GTOWirelessExitSensorinstructionmanualforgeneralinstallationguidance. Rev.12/01/08•PrintedinChinaforGTO,Inc. Signal Cable Vehicle Sensor RB709U-NB Universal Receiver Module Cover Electronics/Transmitter Module Programmable Dip Switches How it works: TheGTOwirelessexitsensorconsistsofavehiclesensor,transmitter,andprogrammabledipswitches. Themaximumrangebetweentransmitterandreceiveris80-100ft. Thetransmittermoduletransmitsaspec

Parts Included: .............. ABCFGHCED A. Solar Panel B. Lag Screws (4) C. Pipe Clamp (4) D. Curved Pipe E. 1/4" Nuts (4) F. 1/4" x 1/2" Bolt (4) G. Wire Nuts H. Compass Tools Required : • Slotted (flat blade) Screwdriver • 7/16" open end wrench For more information on Mighty Mule’s full line of automatic gate openers and access controls visit our website at ©2007 GTO, Inc. RB905 Rev. 11/5/07 Printed in China for GTO, Inc. 2 Solar Panel Installation Step 1: Slide the 1/4" bolts (F) through the

All necessary mounting hardware can be obtained from your local hardware store; all other hardware is provided. This manual shows two examples of the most common installations, and should provide insight into most other applications. If you have any questions during installation, please call (800) 543-1236 for technical support. For more information on GTO's full line of automatic gate openers and access controls visit our website at RB909 rev-10/19/07 © GTO, Inc. 2007 Printed in China for GTO,

LISTEDUSTWO 12VDC, U1, 230A BATTERIES ARE REQUIRED BUT NOT INCLUDED. DO NOT Install This Operator Without Safety Edges and Photo Beams! APPROPRIATE ENTRY/EXIT DEVICES WILL BE REQUIRED - SEE YOUR DEALER. For more information on GTO’s full line of automatic gate openers and access controls visit our website at GPSW050 rev - 04/07/Printed in China GTO, inc. The GP-SW050 automatic gate operators are intended for use with vehicular swing gates. The operators can be used in Class I, II, III, and IV ap

Failure to follow installation and safety instructions can result in hazards developing due to improper assembly. You agree to properly install this product and that if you fail to do so GTO, Inc. shall in no event be liable for direct, indirect, incidental, special or consequential damages or loss of profits whether based in contract tort or any other legal theory during the course of the warranty or at any time thereafter. The installer and/or user agree to assume responsibility for all liabil

AUX OUT SOLARPANEL18VAC LINK RCVR GRN BLK RED EXIT SAFETY EDGE CYCLE COMMON Mighty Mule 352 Connecting Accessories Connecting Accessories CHARGING POWER RF AUX OUT SOLAR PANEL 18VAC RCVR GRNBLKREDEXITSAFETYEDGECYCLECOMMON LINK GTO Photo Beams GTO Loop Detector GTO Automatic Lock Mighty Mule Push Button Control According to Application Mighty Mule Vehicle Sensor Refer to Vehicle Sensor manual for additional connections. Edge Sensor ON 10DIP NO COM NC V + V – LOOP LOOP LOOPNOTE:Connections are for

Do not exceed 1000'. NOTE: Pull approximately 1 foot of extra low voltage wire into the control box to accommodate terminal connections. To maintain adequate charging power, use appropriate gauge, stranded, direct burial wire (see Accessory Catalog). Do not use telephone wire or any solid core wire because it will not provide adequate current. Never splice wires together. RED BLK ORG BLU GRN CLS EDG OPN EDG RED GRN ORG BLU WHT BLK ORG BLU GRN CLS EDG OPN EDG LEARN AUTO CLOSE INERTIA STATUSSTATUS

Disconnect operator ONLY when the gate is NOT moving. TO MANUALLY OPEN AND CLOSE THE GATE: 1. Lift quick release pins UP, then pull them OUT of chain brackets. 2. Lay chain down and manually slide gate to desired position. Series GTO, Inc. Tallahassee, Florida USA SL .. Conforms to UL 325 STANDARDS Certified to CAN/CSA-C22.2 No.247-92 • Fingers, hands, and loose clothing may be dragged into chain sprockets. • Fingers and hands can be injured by rotating sprockets. • Keep hands, fingers, and loos

AUTOMATIC GATE OPERATOR FOR VEHICULAR SWING GATES INSTALLATION MANUAL FOR THE PROFESSIONAL INSTALLER Receiver Run 1000' (max.) of low voltage wire to control box from transformer. (wire not included) 120 Volt Indoor Transformer (surge protector not supplied) PVC conduit (not included) to protect wire from lawn mowers and weed eaters. Control Box with Battery Power Cable Closed Position Positive Stop Plate Gate Bracket Post Bracket Assembly GTO/PRO 2000 Warning Sign WARNING! READ ALL INSTRUCTIONS

Keep in mind that the gate operator is just one component of the total gate operating system. Each component must work in unison to provide the consumer with convenience, security, and safety. This manual contains various safety precautions and warnings for the system designer, installer, and consumer. Because there are many possible applications of the gate operator, the safety precautions and warnings contained in this manual cannot be completely exhaustive in nature. They do, however, provide