Remove logo from existing bottom louver with pre-drilled holes and then snap the logo into the brass or brushed stainless louver with pre-drilled holes. Step 7. Reinstall the louver assemblies, reusing the existing screws to reinstall the bottom assembly. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your loca

The kits contain seven louvers plus one louver with two pre-drilled holes (eight total) and these instructions. INSTALLATION INSTRUCTIONS Step 1. Turn off the fireplace and allow it to cool before proceeding. Step 2. Slightly lift and pull the existing top louver assembly away from the fireplace. Step 3. Slightly lift up the bottom hinged panel to disengage the small hooks on ether side of the panel. Pull forward and lower the panel down to open. Remove the assembly from the fireplace by rem

This should meet the requirements of the Building Regulations for the fire to be fitted and the fuel to be used. This should be provided using a permanently open air vent, which is positioned so that it is not liable to be blocked both inside and outside the building. If any of these checks reveal problems do not proceed with the fitting of the fireplace until they have been rectified. Dimensions Fitting optional insert panel (8904) The insert panel is fitted to the back of the main front pa

If a cement infill is required to achieve this, do not proceed with the installation until the cement is completely dry. Cover the surface of the hearth to protect it from damage during installation of the cast panel. Protect the surfaces of the surround (mantelpiece) from damage when trial fitting of the panel. Position the front panel centrally in the fireplace opening against the wall. Place the surround (mantelpiece) in position and, holding it firmly against the wall, pull the front pane

Only genuine Stovax replacement parts are to be used to keep your fireplace in safe and efficient working order. After any chimney fire it is recommended that the chimney system be inspected and swept by a NACS registered (UK only) chimney sweep, to confirm that the system is structurally sound and free from any obstructions before re-use. MAINTENANCE For fully polished fireplaces Stovax Steel Cleaner (Part No. 2037) is recommended to keep them clean and rust free. If a fire is not to be lit f

Should any conflict occur between these instructions and these regulations then the regulations shall apply. All electrical connections should meet the requirements of UK Building Regulations (England and Wales - Document P/ Scotland - Part N). Your local Building Control Office would be happy to advise should questions arise, regarding the requirements of the regulations. The fireplace should be fitted by a HETAS (CB only) registered installer, or approved by your local building control offi

4.1 Back Panel The back panel hooks onto a wall bracket (supplied). • Find the fire's centre point across its width and mark • Mark 1081 mm from the hearth or base of appliance (if wall mounted) to establish the correct height • Centre the wall bracket above the fire and at the distance from the hearth or base of appliance (if wall mounted) shown in Diagram 1 1AR2170height measured to the centre top of bracket = 1081mmcentre point1081mm 4.2 To fix the wall bracket: • Secure the bracket into plac

SECURING FUSION FRAME TO THE FIRE 3.1 Access to the controls is behind the drop down lower cover. There are two fixing brackets either side of the controls: • Secure frame to the firebox at the base with screws supplied to ensure rigid fixing, Diagram 3 3AR2169 USER INSTRUCTIONS 1. CONTROLS ACCESS To access the fire's controls with a Futura Frame fitted: • Push the control panel firmly in the centre to release the magnetic catch Details of the controls (and Replacing the Batteries, if applicable

2. CLEANING THE FRAME Only clean the frame when it is cold. The painted frame of the Fusion should be cleaned using a damp cloth and buffed with a lint free duster. INSTALLATIONINSTRUCTIONSCovering Models 8699GP and 8699 IR1. GENERAL 1.1 These instructions are supplemental to, and must be read in conjunction with, the Installation Instructions (PR0741 for E-Studio & Logic E-Box Conventional Flue and the Balanced Flue version in PR0776) supplied with the fire. 1.2 Fitting of the Fusion frame must

The symptoms of poor performance related to wet wood include: •Difficulty getting a fire going and keeping it burning well • Smokey fires with little flame • Dirty glass • Rapid creosote build-up in the chimney • Low heat output • Short burn times, excessive fuel consumption and blue/grey smoke from the chimney. To help avoid large build-ups of tar and creosote within the stove and the flue system, it is recommended to burn at high output for at least 30 minutes each day. The use of Stovax Prote