Removal • If connected, disconnect the Versa-Tether® from the tether anchor. • Release each LATCH harness from the LATCH anchor by pressing the red release button on the LATCH connector. • When not in use, always store the LATCH connectors in storage pouches sewn in cover above rear-facing lock-offs. D E 11 Installation: Rear-Facing Lap-Shoulder Belt Installation • Figure A illustrates a typical rear-facing lap-shoulder belt installation. • When not in use, always store the LATCH connectors in s

All rights reserved. Printed in USA P464800_R1:03.11 This product and its components are subject to change without notice. Section TitleWARNING! DEATH or SERIOUS INJURY can occur: WARNING! DEATH or SERIOUS INJURY can occur: • Harness mode: use only with children who weigh between 25 and 85 lbs (11.3 and 38.6 kg) and whose height is between 30 and 57 in. (76.2 and 144.8 cm) and are at least 2 years of age. • Booster mode: use only with children who weigh between 40 and 120 lbs (18.1 and 54.4 kg)

Advocate® 70 CS User Guide IMPORTANT:Thoroughly read and follow all instructions before installing this child seat. Store this user guide in the pocket behind the cover (See features pages for reference). Table of Contents Table of Contents Safety Information.......................................................................................2 Warnings...............................................................................................................2 Important Notes................

Doing so could cause the child seat not to perform as intended. Forward-Facing Installation Forward-Facing Installation 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow and unbuckle the harness. 3 Pull the head restraint cover up, then pull the seat cover forward to access the forward-facing belt path. 4 Route the vehicle seat belt through the forward-facing belt slots, then buckle. Ensure the vehicle belt is not twisted. 5 Push the

33IMPORTANT: • The harness buckle strap should lie toward the back of the child seat during installation. • The buckle should be in the inner slot for rear-facing installation. 34 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow, unbuckle the harness, and remove the belly pad. 3 Pull the head restraint cover up, then pull the seat cover forward while pulling the buckle through to access the rear-facing belt path. IMPORTANT: Ensure bu

Certification............................................................................ Registration............................................................................ Weight Range/Maximum Height............................................ Installation: Aircraft............................................................................... Features Front View.............................................................................. Rear View........................................

See Figure F. Raise or lower seat to desired height. Make sure the knob locks into place once the seat is at the desired height. TO USE WITH TRAY: For children who do not sit at the table, a large tray is included that attaches easily to the seat with one simple step. Step 1: Slide tray on from the front. Make sure it locks into place. See Figure G. To remove, pull up the two locking tabs underneath and slide off. TO USE AS A TODDLER CHAIR: To use as a toddler chair follow these easy steps

Le plateau n'est pas destiné à maintenir l'enfant en place dans le siège. • TOUJOURS bien fixer les sangles du dossier ET celles du siège. • Ne JAMAIS laisser l’enfant pousser contre la table. • Ne JAMAIS soulever le produit avec l’enfant dedans. • Lire les instructions dans leur intégralité avant toute utilisation. • À conserver afin de pouvoir s’y reporter ultérieurement. • Ne pas utiliser ce produit s'il est endommagé ou cassé. • À utiliser EXCLUSIVEMENT pour un enfant qui se tient ass

We recommend that you retain your receipt and attach it to this user guide. They should be kept in a safe place. Britax does not accept liability for damage arising from abuse, misuse or negligence. This guarantee is not transferable and therefore does not apply to second-hand products. Your statutory rights are not affected by this guarantee. If in doubt ............................................................ For advice as to the suitability of this restraint for your car please use on our

E). • If your vehicle is equipped with an automatic locking retractor (ALR), use of lock-offs is not required as long as ALR is activated. Check your vehicle’s owner’s manual to determine type of retractor your vehicle has, and for proper use of retractor. 8Verify all connections are secure and restraint is stable. The restraint is secure when it cannot be moved front-to-back or side-toside more than 1” (2.5 cm.) at belt path. If restraint is not secure, repeat procedure or use an alternate seat