ST Indicates heater is in standard mode. Ec Indicates heater is in economy mode. SL Indicates heater is in sleep mode. 9800 Electronic Control Operation When first powered up, the 9800 electronic system will perform a self-diagnostic check and then it will automatically heat to and maintain a temperature of 100°F (37.5°C) until you change the set temperature as listed in the “Temperature Adjustment” section below. These instructions will describe features and options that your particular spa may

first 24 hours. Put the cover on and allow the spa to heat to desired 17. temperature. Adjusting The Proper Bromine Levels After start up, decrease the filtration cycle to F-4 1. and monitor the bromine level until it is within the recommended range. Use bromine test strips to achieve a 3-5 ppm 2. recommended level. Note: It can take several days for the bromine level to stabilize because the fill water that was used sometimes contains contaminants that need to be neutralized, thereby using up t

Do not use extension cords! Always use a weatherproof-covered receptacle. Receptacle shall be located not less than 5 feet (1.5 m) from and not exceeding 10 feet (3.0 m) from the inside wall of the spa. (NEC 680.43(A)) Do not bury the power cord. If your cord becomes damaged, replace it before next usage. All 120V spas must have a GFCI. This can be either a 20 amp GFCI receptacle or a 20 amp GFCI cord and plug kit as shown (CKIT110 - P/N ELE09700086). Test the GFCI plug prior to first use and pe

During this time the pump will run at a maximum speed. In the off position, press the “PULSE MODE” • button once. The green power light will flash to indicate reset.• Multi-Colored Spa Light Operation Turn the spa light on by pressing the “LIGHT” 1. button on the topside control panel. To filter through the different color choices, press 2. the button on and off. Each time you press the button, you advance to the next color. To turn the spa light off when not in use, press the 3. “LIGHT” button.

Customer Service Department 1462 East Ninth Street Pomona, CA 91766 Toll Free: 1-800-CAL-SPAS Fax: 1-909-629-3890 Copyright 2004, 2005 California Acrylic Industries, Inc. All rights reserved. Duplication without written consent is strictly prohibited. Cal Spas™, Adjustable Therapy System™, ATS™, Bio-Clean™, Cal Balance™, Cal Entertainment System™, Cal Zone Quest 1000™ and Cal Zone Quest 2000™, Cal Sweep™, Cal Select™, Fitness Spa Series™, Spa Cal™, and XL Heat Exchanger are registered trademarks

120 Volt Electrical Installation Always follow applicable local, state and federal codes and guidelines. Use only a dedicated electrical line with a 20 amp breaker. Cord-and-plug connections may not use a cord longer than 15 feet (4.6 m) and must be plugged into a dedicated 20 amp GFCI connection (NEC 680.42(A)(2)). Do not use extension cords! Always use a weatherproof-covered receptacle. Receptacle shall be located not less than 5 feet (1.5 m) from and not exceeding 10 feet (3.0 m) from the ins

(Displays on third occurrence of dr message.) Spa is shut down. Follow action required for dr message. Spa will not automatically reset; you may press any button to reset. Pr When your spa is first actuated, it will go into priming mode. The priming mode will last for up to four minutes and then the spa will begin to heat and maintain the water temperature in the Standard mode. --F or --C Temperature unknown After the pump has been running for two minutes, the temperature will be displayed. - -

The panel will display “TEMP LOCK” when the set temperature is locked. To unlock the set temperature: Press the “UP” or “DOWN” button, “TIME”, “JETS 1”, and then the “DOWN” button. Circulation Pump This is an optional feature. The circulation pump will come on when the system is checking temperature, during filter cycles, during freeze conditions, or when another pump is on. Preset Filter Cycles There are two filter cycles per day. The start and end times of each cycle are programmable. To progr

. . . . . . .4 Preparing a Good Foundation . . . . . . . . . . . . . . . . . . .5 Assembling Your Sauna CU-210 Sauna Assembly . . . . . . . . . . . . . . . . . . . . . . .8 CU-300 Sauna Assembly . . . . . . . . . . . . . . . . . . . . . 14 CU-400 Sauna Assembly . . . . . . . . . . . . . . . . . . . . . 21 OD-100 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 OD-200 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Light Installation (Inside and Outside) . . . .

out. Place the dirty filter into a bucket of water deep enough to cover the filter. Add 8 oz of Cal Spas “Liquid 2. Filter Cleaner” to the bucket of water. Note: It is a good idea to keep a spare filter to use in the spa while the dirty filter is being deep cleaned. This way, you can rotate the filters and both will last longer. Twist off the tablet tube and set it aside3. Soak the filter for a minimum of 24 hours.4. Spray the filter with a water hose. Spray each pleat carefully.5. Put fresh bro