Zip Ties (4) 2. Keys (2) 3. 1/4”-20 Screws (4) 4. M5 Screws (4) Tools required for installation: • 3mm Hex Drive (For attaching Mounting Bracket to Docking Station with M5 Screws) • 5/32” Hex Drive (For attaching Mounting Bracket to Motion Device with 1/4”-20 Screws) Port Replication Capability Side Connectivity Rearward Connectivity *(Antennas for DS-DELL-101-3 only) Mouse Keyboard Antennas* (Wi-Fi, GPS, Cellular) Microphone Parallel (DB-25) VGA Display (x2) (HDMI Dongle Required) eSATA Headpho

6) Power on computer. The Laptop Power Button LED will illuminate blue to indicate proper system function. Once docked, the Laptop Power Button may be used to power computer on/off. Lock Laptop Power Button / LED Operation - Undocking 1) If previously locked, unlock Docking Station using supplied key. 2) To release Latch Handle, press in the Lock, and the Latch Handle will spring open to the Unlatched position. Note: Red warning label on Latch Handle is visible when fully extended. 3) Once unlat

declares that their DS-DELL-100 & DS-DELL-220 SERIES DOCKING STATIONS: Are classified within the following EU Directives: EU Electromagnetic Compatibility Directive 2004/108/EC, 2009/19/EC And further conform with the following EU Harmonized Standards: EN 55022 (2006) + A1 2007, EN 55024: 1998 + A1: 2001 + A2: 2003 EN 50498: 2010 Clause 7.1 Broadband Radiated Disturbances - Quasi-Peak Clause 7.2 Narrowband Radiated Disturbances - Average Clause 7.3 Conducted Radiated Disturbances - Severity Leve

Collect cables to secure to the mounting system (Note: mounting system not included) 8 Operation - Docking • DO NOT MATE COMPUTER TO DOCKING STATION UNLESS COMPUTER’S DOCKING CONNECTOR ACCESS DOOR IS FULLY OPEN OR DAMAGE MAY RESULT. • DO NOT FORCE LAPTOP ONTO DOCKING STATION. IF THERE IS RESISTANCE, CHECK ALIGNMENT OF COMPUTER ON DOCKING STATION. 1) To load the computer, first ensure Docking Station is unlatched by pushing the Lock to release the Latch Handle. Once Docking Station unlatches, rel

For questions regarding the set-up of your DS-DELL-100 Series/220 Series Docking Station, please contact Havis at 1-800-524-9900 or visit for additional product support and information. This Owner’s Manual applies to the following Part Numbers: DS-DELL-101 DS-DELL-101-3 DS-DELL-103 DS-DELL-221 DS-DELL-223 • NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE. • DO NOT USE COMPUTER WHILE DRIVING. • READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION. •

declares that their DS-PAN-410 SERIES DOCKING STATIONS: Are classified within the following EU Directives: EU Electromagnetic Compatibility Directive 2004/108/EC And further conform with the following EU Harmonized Standards: EN 55022 (2006) + A1 2007, EN 55024: 1998 + A1: 2001 + A2: 2003 EN 50498: 2010 Clause 7.1 Broadband Radiated Disturbances - Quasi-Peak Clause 7.2 Narrowband Radiated Disturbances - Average Clause 7.3 Conducted Radiated Disturbances - Severity Level 2 Dated: August 4, 2011 P

Torque screws to 80 in-lbs (9.0 Nm) ± 10%. 1/4”-20 Screws 6 Cable Management 1) Tip the Docking Station to a position that is comfortable to work with. 2) Install all cables that are necessary for computing needs. 3) Use Zip Ties (Hardware Kit Item 1) to strain relieve cables at rear of Docking Station. IF SECURING EXTERNAL ANTENNAS TO DOCKING STATION (DS-PAN-411-2, DS-PAN-412-2, PKG-DS-PAN-412-2) LEAVE AN ADEQUATE SERVICE LOOP BETWEEN THE ANTENNA CONNECTOR AND THE FIRST ZIP TIE ON THE DOCKING S

For questions regarding the set-up of your DS-PAN-410 Series Docking Station, please contact Havis at 1-800-524-9900 or visit for additional product support and information. This Owner’s Manual applies to the following Part Numbers: DS-PAN-411 DS-PAN-411-2 DS-PAN-412 DS-PAN-412-2 DS-PAN-413 PKG-DS-PAN-412 PKG-DS-PAN-412-2 • NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE. • DO NOT USE COMPUTER WHILE DRIVING. • READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING

4) Gather all cables to one side and tie off to unused holes on underside of Docking Station. Insert as many zip ties as necessary to secure cables. 7 • 1-800-524-9900 Cable Management (continued) 5) Create a service loop with cables to ensure that no tension is on the connectors and to enable intended motion. 6) Tie off cables onto a stationary part of the mounting system. This loop must be large enough to allow full range of expected rotation and extension without stressing connections. Collec

• THE ANTENNA MODULE IS NOT A HANDLE. DO NOT USE IT TO CONNECT OR ENGAGE THE COMPUTER TO DOCKING STATION. DO NOT USE IT TO CARRY THE DOCKING STATION. • THE DS-PAN-410 SERIES DOCKING STATIONS ARE DESIGNED EXCLUSIVELY FOR USE WITH PANASONIC CF-53 TOUGHBOOK COMPUTERS ONLY AND ARE NOT BACKWARD COMPATIBLE WITH THE PANASONIC CF-52 COMPUTER • FOR DOCKING STATION MODELS EQUIPPED WITH AN INTEGRATED POWER SUPPLY (DS-PAN-412, DS-PAN-412-2, PKG-DS-PAN-412, PKG-DS-PAN-412-2), REFER TO THE SUPPLIED LIND POWER