Enamels, lacquers, polyurethane, urethane top coats (including basecoat/clearcoat) and all primers can be applied. The spray gun has fluid and pattern controls. This spray gun is supplied with a 20.3 oz (600 ml) gravity feed cup. Description Le HDS590 est un pistolet vaporisateur à alimentation par gravité HVLP conçu pour la pulvérisation de matériaux de viscosité légère à moyenne. Appliquez les émaux, les laques, le polyuréthane, les couches de finition uréthane (y compris couches de fondatio

It is easily and quickly convertible from pressure to siphon feed. Both External and Internal mix air caps can be used. It can also be converted for use with a separate pressure paint tank for large jobs. Description Ce pistolet de pulverisation tout usage est concu pour l’usage domestique, commerciale et sur la ferme. Il peut utiliser tout type de peintures et materiaux, y compris le latex et les emaux lourds, en mode d’alimentation sous pression. On peut le convertir facilement et rapidement d

Replace the screw. 4. Reconnect the air supply to the impact wrench and run for 20 to 30 seconds. Lubricate the entire impact mechanism by rotating the tool upside down and sideways while running the tool. 5. Remove the screw and hold the oil port hole over a suitable container to allow excess oil to drain. 6. If the oil is dirty, repeat the procedure above until the oil comes out clear. Install the screw and tighten. The residual oil remaining in the impact mechanism chamber is all that is need

4. Connect the impact wrench to the air supply and cover the exhaust port with a towel (See Figure 1). Run the impact wrench in both the forward and reverse directions for 20 to 30 seconds. Oil will discharge from the exhaust port when air pressure is applied. Impact Mechanism Lubrication. The impact mechanism should be lubricated monthly. ! WARNING ! DISCONNECT THE IMPACT WRENCH FROM THE AIR SUPPLY BEFORE LUBRICATING. 1. Disconnect the impact wrench from the air supply. 2. Remove the allen head

FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE. RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. Description Do-It-Yourself (DIY) impact wrenches are air tools designed for removing and installing nuts and bolts such as lug nuts, exhaust system clamps, etc. Unpacking When unpacking this product, carefully inspect for any damage that may have occurred during transit. Make sure any loose fittings, bolts, etc., are tightened before putting this product into serv

S’il vous plait fournir l’information suivante: - Numero du Modele - Numero de Serie (si present) - Description de la Piece et son numero sur la liste Sirvase darnos la siguiente informacion: - Numero del Modelo - Numero de serie (de haberlo) - Descripcion y numero del repuesto segun la lista 47 48 49 12 11 10 13 27 14 51 1 3 4 46 33 35 40 41 39 54 29 28 2 15 20 19 16 18 5 8 6 9 37 7 38 32 30 45 22 38 16 17 21 25 55 50 26 36 38 53 23 44 43 42 31 52 34 24 Ref. No. Part Number Qty. No de Ref. Nume

Grounded Outlet Grounding Pin Figure 2 - Grounding Method MOISTURE IN COMPRESSED AIR Moisture in compressed air will form compressor pump. When humidity is high use for an extended period of time, this moisture hose. When using a paint spray or sandblast the tank through the hose, and out of the gun material. IMPORTANT: This condensation will cause water spots in a paint job, especially when spraying other than water based paints. cause the sand to cake and clog the gun, rendering it ineffective

6. Do not stand on or use the pump or unit as a handhold. 7. Before each use, inspect compressed air system and electrical components for signs of damage, deterioration, weakness or leakage. Repair or replace defective items before using. 8. Check all fasteners at frequent intervals for proper tightness. Do not operate unit if damaged Record the Model No., Serial No. and date of purchase located on the base below the pump in the space below. Model No. ____________________ Serial No. ____________

IMPORTANT: Locate unit as far from spraying area as possible. LUBRICATION This is an oilless NOTICE type compressor requiring no lubrication. THERMAL OVERLOAD PROTECTORS This compressor is ! CAUTION equipped with automatic reset thermal overload protectors which will shut off the motor if it becomes overheated. If thermal overload protectors shut motor OFF (O) frequently, look for the following causes. 1. Low voltage.. 2. Lack of proper ventilation. 3. High ambient temperature. If the thermal !

Read product described. Protect yourself and others could result in personal injury and/or property damage! QUALITYASSURANCEPROGRAM Need Assistance? Call Us First! 1-800-543-8622 Portable Handheld Air Compressor Description ! DANGER Portable oilless air compressors are for home and workshop use. All models Breathable Air Warning are equipped with regulators, needle This compressor/pump is not and ball bearings, and motors with equipped and should not be used automatic overload protection. “as is