SHEET DESCRIPTION QTY/PER KEY PART NO. SHEET DESCRIPTION 7 1 C100005 1 HONDA 5.5 hp ENGINE w/DEFLECTOR 1 C100114 1 HONDA 8.0hp ENGINE w/DEFLECTOR 2 C100028 1 PULLEY w/ HUB & BOLTS, 4" x 22mm 3 C100024 1 B56 V-BELT, 5.5hp MODEL 3 C100113 1 B59 V-BELT, 8.0hp MODEL 4 C500011 1 3/16" x 1 3/4" SQUARE KEY 5 C500029 2 1/4" x 3/4" BOLT 6 C100023 1 HUB, TAPERLOCK 7 C100022 1 PULLEY, TAPERLOCK 8 C100008 1 REDUCTION BOX, and KEYS 9 C500174 8 1/2" x 1 3/4" BOLTS 10 C500042 8 3/8" FLAT WASHER 11 C200031 1 PU

1028 Street Road . Southampton, PA 18966 Telephone: 1-800-366-6268 TABLE OF CONTENTS INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Thank You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Read This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Se

9. Servicing the sod cutter regularly and correctly. 10. Classen Mfg., Inc. parts and service. 11. Give the customer the operators manual and encourage customer to read it. DATE DELIVERED __________/__________/__________ SIGNATURE _______________________________________ SAFETY ENGINE STARTING PROCEDURES HANDLE FUEL SAFELY -AVOID FIRES Handle gasoline with care; it is highly flammable. Use an approved gasoline container. Fill the fuel tank outdoors. DO NOT fill tank completely full. DO NOT smoke

All transportation charges on parts submitted for repair or replacement under this warranty shall be borne by the purchaser. This warranty does not include engines or engine parts, tires, batteries, or gearboxes that are covered under separate warranties furnished by their manufacturer or supplier, nor does it include normal maintenance parts, including but not limited to, spark plugs, points, filters, blades, and lubricants. All service under this warranty will be furnished or performed by our

Maximum engine rpm is recommended for smooth operation. 8. After cutting a short distance, stop machine by letting the twist grip throttle control go back to its original position. Check thickness of cut and adjust if necessary. 9. At the end of each cutting pass, lift up on the handle bar to clear the cutting blade from the sod. Retard the throttle control and turn machine around into the position for the next cut. 10. When finished cutting sod, reverse steps 6 through 3, leaving the wheel driv

3. Weight bar installed. 4. Gas lever on engine turned on. 5. All lubrication points greased. 6. 6:1 gearbox oil level. 7. Engine oil level. 8. Air cleaner. 9. Touch up scratches. 10. Chain(s) tight. 11. Lowering handle working properly. 12. Control handle(s) working to tighten V-belt(s). 13. Add fuel, start engine, test run. DATE SET UP __________/__________/__________ DELIVERY CHECK LIST Review the operators manual with the customer. 1. Classen Mfg., Inc. warranty. 2. Safe operation and servic

SHEET DESCRIPTION 26 500008 1 3/8" X 2" BOLT W/ LOCK WASHER & NUT 27 500099 2 3/8" X 1-1/4" BOLT W/ FLAT WASHER, LOCK WASHER & NUT 28 500098 3 3/8" X 3-1/2" BOLT W/ (2) FLAT WASHERS, LOCK WASHER & (2) NUTS 29 300037 1 PLATE, ADJUSTER 30 500005 4 5/16" X 1-1/2" BOLT W/ LOCK WASHER & NUT (NOT SHOWN) 31 300009 1 WEIGHT STOP 32 _ 300071 1 PLATE, HANDLE BRACE GUSSET 33 500051 6 3/8" X 1 " BOLT W/ LOCK NUT 34 100037 1 ENGINE W/ EXHAUST DEFLECTOR, 4HP HONDA 35 400115 1 BRACE, HANDLE 36 500114 2 5/16" X

REAR AXLE SUPPORT 40 100073 1 LUBRICATION TAG (NOT SHOWN) 18 500071 2 1/4" x 5/8" FINE BOLT 41 100074 2 DECAL, "CLASSEN" (NOT SHOWN) 19 500137 6 1/4" LOCK WASHER 42 100096 1 DECAL, "ALL GUARDS" (NOT SHOWN) 20 500164 4 1/4" FENDER WASHER 43 300079 2 WHEEL PIVOT FLAT 21 500029 4 1/4" x 3/4" BOLT 44 500083 2 5/16" FLAT WASHER 22 500136 4 1/4" NUT 45 500078 2 "E" RING 23 100250 2 SPRING 6 Parts Power Train and Tine Rotor Assembly CA-18 COMPACT AERATOR KEY 1 1 2 3 4 5 6 7 8 9 10 11 500159 1 3/8" x 2-

000252 & UP) PARTS LIST KEY PART NO. SHEET DESCRIPTION 38 500115 2 WASHER, 5/16" LOCK 1 400073 1 FRAME, MAIN 39 500101 2 NUT, 5/16" 2 100086 1 DRUM, WATER 40 300049 2 PLATE, CHAIN TIGHTENING 3 500015 3 1/4" X 3/4" BOLT W/ LOCK WASHER & NUT 41 100013 2 BEARING W/ COLLAR, 3/4" PILLOW BLOCK 4 500011 6 KEY, 3/16" X 1" SQUARE 42 500010 4 5/16" X 1-3/4" BOLT W/ (2) FLAT WASHERS, LOCK WASHER & NUT 5 200012 1 SHAFT, KEYED 43 100041 1 9" PULLEY W/ 3/4" HUB & 3/16" SQ. KEY 6 500054 2 WASHER, (3) 3/4" FLAT