Before you begin your installation, please read these instructions carefully and keep these instructions for future reference. INTRODUCTION The 24746 Futura™ Outdoor TV Antenna is specially designed for digital terrestrial broadcasting reception. The compact and stylish housing can be placed in low visibility locations. Features: • Compact and Stylish Design • Digital HDTV Ready Package Content: • Futura™ Outdoor Antenna • Adjustable Wall Mount Bracket • Instruction Manual Product Description: T

Make sure the antenna is connected to the connector on the rear of your TV as shown above. 2. Set your television to the lowest channel number available in your area, which is usually the most difficult station to receive. 3. Fully extend the rabbit ears, and place them as horizontal as space permits. You may find that you do not need to extend the rabbit earsall the way for good performance. 4. Adjust the rabbit ears, and rotate the entire antenna until you find the position that gives you the

Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured equipment at Linear’s discretion. The customer is always responsible for shipping and handling charges to the repairs facility. Linear will pay return shipping and handling charges on “in warranty” products shipped back to the customer. The customer will be billed for the return shipping and handling charges on “out of warranty” products. There will be a 50% expedite fee for any express requests. The I

Locate the two door chime wires emanating from the existing door chime circuit. Test the door chime by touching the two wires together, completing the circuit. If door chime does not sound,check transformer or chime. Turn off power. Attach one wire to each of the screw terminals on the back of the button. Mount button in desired location with two screws provided. Install according to applicable local electrical codes. -EEL Wall

Locate the segments around the outer edge of the timer’s dial. These segments, each representing 15 minutes, can be pushed out and away from the edge of the dial (try using the tip of a pen or pencil). Conversely, segments that have been pushed out can be easily pushed back in by hand. Be sure all segments are pushed in before programming. Select a time period (or periods) you want the appliance turned on, then push out ALL the segments that fall on or within that time period. For example, to ha

Notice ALL segments between 10 PM and 2 AM have been pushed out. Current time is 8:00 PM. CurrentTimeCurrentTimeCurrentTime24 Hour Outdoor Timer Instructions: 1. Locate the segments around the outer edge of the timer’s dial. These segments, each representing 15 minutes, can be pushed out and away from the edge of the dial (try using the tip of a pen or pencil). Conversely, segments that have been pushed out can be easily pushed back in by hand. Be sure all segments are pushed in before programmi

4. With your device on, press ON•OFF. If the device turns off, no further programming is required. Note: If some buttons do not operate your equipment, try one of the other codes for your brand. Write your codes down here for easy reference later. Device Device stored Code TV TV VCR CBL/SAT DVD/AUX 7 CodeSearch If your device does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps. 1. Manually turn o

To install the batteries: 1. On the back of the remote, push down on the tab and lift the cover off. 2. Match the batteries to the + and - marks inside the battery case, then insert the batteries. 3. Press the battery cover back into place. Button Description Button Description INDICATOR LIGHT The Indicator Light flashes to show that the remote is working. POWER The POWER button operates the same as your original remote (note: some RCA, GE and ProScan models require you to press the devic

Next, connect the base unit to an existing phone jack using six-foot phone cord (included); then connect the phone to the unused connector on the base unit. El iûm\ Wall Jack Base Unit 2. Plug the extension unit (single phone connector on right side) into an AC outlet where connection is needed. The indicator light on the extension unit will blink red. As soon as it recognizes the base unit, the indicator light will then illuminate green; the indicator light on the base unit will also illum

Please retain this guide for future reference. Table of Contents Install the Batteries 1 Button Description 2-4 Programming for TV 5 Programming for VCR 6 Programming For DVD 7 Programming For DBS System 8 Programming For Cable 9 Programming For Audio 10 Programming For Second Device 11 Operating Audio Function 12-13 Sleep Functions 14 Programming With Code Search 15 Identifying Codes For Your Remote 17 Warranty 18 Lost Codes 18 This Universal Remote Control is already programmed for most GE, RC