Log:

Ryobi Reciprocating Saw

Downloads : 2 Arquivo Tamanho: 107 kb    Fabricante : Ryobi  
Categoria : Jig Saw e

It runs through normal 120-V alternating current power. When on, the saw blade has a stroke of 19/16 inches moving at a maximum speed of 2800 strokes per minute. The entire assembly, including the removable blade, weights 6.3 pounds. The saw has 6 speed settings, a trigger which determines whether the saw is on or off, and interchangeable blades. After completing the model and assembling it, we will attempt to animate several aspects of the construction and functions of the saw. Finally, we will

Ryobi SGL1150

Downloads : 9 Arquivo Tamanho: 229 kb    Fabricante : Ryobi  
Categoria : Máquinas e acabar

Following this rule will reduce the risk of serious personal injury. The key to efficient operation begins by controlling the pressure and surface contact between the grinding wheel and workpiece. Flat surfaces are ground at an acute angle, normally between 5 to 15 degrees. For maximum control, hold the grinder in front and away from you with both hands, keeping the grinding wheel clear of the Fig. 8 TRIGGER SWITCH LOCK-ON BUTTON 5° TO 15° Fig. 7 workpiece. Start your grinder and let the motor a

Ryobi TB190

Downloads : 0 Arquivo Tamanho: 236 kb    Fabricante : Ryobi  
Categoria : Sistemas de ventilação

Weight 75 lbs Warranty 2-year limited QTRBY-BUT BUILT FOR LIFE?

Ryobi TB4BP

Downloads : 0 Arquivo Tamanho: 236 kb    Fabricante : Ryobi  
Categoria : Sistemas de ventilação

Weight 75 lbs Warranty 2-year limited QTRBY-BUT BUILT FOR LIFE?

Ryobi RJ160V

Downloads : 0 Arquivo Tamanho: 251 kb    Fabricante : Ryobi  
Categoria : Jig Saw e

Make sure saw blade is clear of any foreign material and that power cord and extension cord are out of the blade path. Be sure material to be cut is held firmly. Small work pieces should be securely clamped in a vise or with clamps to the work bench or table. Mark the line of cut clearly. Depress the trigger switch starting the cutting action, set the base assembly against the work, then move the blade into the work. DO NOT FORCE. Use only enough pressure to keep the saw cutting. Let the blade a

Ryobi DBJ50

Downloads : 2 Arquivo Tamanho: 258 kb    Fabricante : Ryobi  
Categoria : marceneiro Placa

Next you would raise the fence 1/4 in. to the desired offset and cut the slots in the legs. Page 12 OPERATION OPERATION T- JOINTS See Figures 11-15. A T-joint is used when the end of a board is joined to the face of another board as shown in figure 11. Attaching shelves to bookcases and inner support braces to frames are typical applications. Actual cutting of a T-joint is as simple as any other cut. However, it is critical that you mark the centerlines, mark the intersection points for each slo

Ryobi RJC180

Downloads : 8 Arquivo Tamanho: 265 kb    Fabricante : Ryobi  
Categoria : Jig Saw e

Failure to do so could result in possible serious personal injury. BLADE WRENCH HOLDER A blade wrench (5 mm hex key) is packed with your saw. A convenient feature on your saw is the wrench holder. This is a slot located on the bottom portion of the saw handle. It is convenient for storing the wrench when it is not being used. BLADE SELECTION Your saw is equipped with a "lock-off" button which reduces the possibility of accidental starting. The lock-off button is located on the handle above the s

Ryobi AG450

Downloads : 0 Arquivo Tamanho: 277 kb    Fabricante : Ryobi  
Categoria : Máquinas e acabar

Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Tool Use and Care ¦ Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. ¦ Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. ¦ Do not use tool if switch does not t

Ryobi RJ150V

Downloads : 0 Arquivo Tamanho: 283 kb    Fabricante : Ryobi  
Categoria : Jig Saw e

VARIABLE SPEED See Figure 2. Your reciprocating saw has a variable speed control selector designed to allow operator control and adjustment of speed and power limits. The speed and power of your saw can be increased or decreased by rotating the variable speed control selector in the direction of the arrows shown in figure 2. NOTE: Hold your saw in normal operating position and turn the variable speed control selector clockwise to increase the speed and power of your saw. Turn counterclockwise to

Ryobi AG400

Downloads : 0 Arquivo Tamanho: 295 kb    Fabricante : Ryobi  
Categoria : Máquinas e acabar

SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alternating Current Type or a characteristic of current n0 No Load Speed Rotational speed, at no load Class II Construction Designates Double Insulated Construction tools .../min Revolutions or Reciprocation Per Minute Revolutions, strokes, surface speed, orbits etc. per minute Safety Alert Symbol Indicates danger, warning or caution. It means attention!!! Yo





categorias