Once a source has been selected, the Select Source Type screen will be displayed. The menu selection immediately defaults to the Learn IR selection in the first screen of the Select Source Type screen (FIG. 25). The source number is displayed at the top of the screen. FIG. 25 Select Source Type - Learn IR .. Learn IR will allow user to learn IR commands for the selected source .. Delay allows user to add a delay to all IR commands learned for the selected source type .. Label allows customizatio

•Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. •AMX lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX lighting products are under warranty. AMX also guarantees the control of dimmable loads that are properly connected to our lighting products. The dimming performance or quality there of is not guaranteed, impart due to the random combina

When done, complete the insertion of the remaining housing latches. 4. Verify that the notches along the bottom of the plastic battery slot separator strip also fit into the three provided alignment holes on the circuit board. 5. Firmly press down around the entire rim of the outer housing to snap the cover back into place. Be careful not to pinch the antenna wire in the housing. 6. Use a grounded Phillips-head screwdriver to insert and re-secure the two housing screws removed in Step 1. 7. Inse

• Refer to the Wireless Security Page section on page 94 for details. EAP-FAST This button opens the EAP-FAST Settings page (FIG. 81 on page 102). “EAP-FAST” security is designed for wireless environments where security and ease of setup are equally desirable. • Refer to the Wireless Security Page section on page 94 for details. Site Survey: The Site Survey tool allows you to detect and view detailed information on all WAPs within the panel’s communication area. Using this tool, you can select a

Input mask operations Input Mask Operators change the behavior of the field in the following way: Input Mask Operators Character Meaning < Forces all characters to be converted to lowercase > Forces all characters to be converted to uppercase ^ Sets the overflow flag for this field Input mask literals To define a literal character, enter any character, other than those shown in the above table (including spaces, and symbols). A back-slash ('\') causes the character that follows it to be displaye

50 diagrams the RJ-45 pinouts and signals for the Ethernet RJ-45 connector and cable. FIG. 50 RJ-45 wiring diagram VG-Series Modero Touch Panels Installation Procedures: 12" and 15" Panels VG-Series Modero Touch Panels Installation Procedures: 17" Panels Installation Procedures: 17" Panels Overview NXT panels are mounted onto flat (horizontal) surfaces in either a stand-alone or combo (NXT atop an NXABASE/ B battery base) configuration. NXD panels are installed into either a pre-wall surface (us

• SSH, HTTPS, and program terminal session timeouts are enabled. • ICSP communication protocol between devices: encryption and authentication are enabled. • Minimum password requirement is 8 characters with at least 1 numeric character. • Login failure attempt pauses 4 seconds before another login attempt is allowed. • After 3 consecutive unsuccessful login attempts, login lockout is enabled for 15 minutes. • Login and logout audit logging is enabled. VG-Series Modero Touch Panels Firmware Pages

The fields on this page are populated with information after the panel is connected to an optional NXA-BASE/B Battery Base containing up to two NXT-BP batteries. FIG. 115 Battery Base page This page is ONLY available on Modero Table Top panels (NXT) using an NXA-BASE/B. The elements of the Battery Base page are described in the table below: Battery Base Page Elements Back: Saves the changes and returns you to the previously active touch panel page. Connection Status icon: This visual display of

Example: SEND_COMMAND Panel,"'*BCB-500.504&510,1,12'" Sets the Off state border color to 12 (Yellow). Colors can be set by Color Numbers, Color name, R,G,B,alpha colors (RRGGBBAA) and R, G & B colors values (RRGGBB). Refer to theRGB Values for all 88 Basic Colors table on page 139. ABCF Set the fill color to the specified color. Only if the specified fill color is not the same as the current color. Note: Color can be assigned by color name (without spaces), number or R,G,B value (RRGGBB or RRGG

.. From the Online Tree tab of the Workspace window, select the NetLinx Master. .. Follow steps outlined in either the Obtaining or Assigning the Master’s IP Address sections from your particular NetLinx Master instruction manual to use an address. .. Note the IP Address and Gateway information. 2. Launch NetLinx Studio 2.3 (default location is Start > Programs > AMX Control Disc > NetLinx Studio > NetLinx Studio 2.3). 3. Select Settings > Master Communication Settings, from the Main menu to ope