To take advantage of these features, spend just a few minutes to browse through this manual to familiarize yourself with your new controller. This booklet is divided into six main sections: • The first section provides a brief description of the controller components and display elements. • The second section takes you step-by-step through the installation process. • The next section provides fundamental irrigation system operation, basic controller operation as well as specific programming

. . . . . . . . Receiver Module . . . . . . . . . . . . Installing the Receiver . . . . . . . . . . . . . . Initial Sensor System Test. . . . . . . . . . . . . . . . . Sensor Module Features . . . . . . . . . . . . . . . . . . . Installing the Sensor Module . . . . . . . . . . . . . . . 10 Freeze Sensor Site Selection. . . . . . . . . . . . . . . . 13 Set Temperature Activation Threshold. . . . . . . . 14 Water Conservation Feature . . . . . . . . . . . . . . . . 15 Smart Bypass Feature. . . . .

– Replace. (c) Damaged riser. – Replace. Poor distribution pattern (a) Nozzle plugged with debris. – Clean or replace nozzle. (b) Nozzle orifice damaged. – Replace nozzle. (c) Low operating pressure. – Determine why system overloaded and correct. 5 A U T O O N Figure 12 100 PSI (7.0 kg/cm2) 80 PSI (5.6 kg/cm2) 65 PSI (4.6 kg/cm2) 50 PSI (3.5 kg/cm2) Main Valve PROBLEM Valve won't close (Electric ) Valve won't close (Hydraulic) Valve won't open (Electric) Valve won't open (Hydraulic) Sprinkler We

Construct or provide triple swing joints for each sprinkler as shown in Figure 1. Use PVC or ABS pipe nipple for the sprinkler connection. Note: On sites where the possibility of heavy equipment rolling over a sprinkler exists, the swing joint will flex preventing damage to the lateral or main lines. On a new installation in raw ground where the sprinklers are to be initially installed above the finished grade and lowered when new turf is established, the swing joint allows sprinkler repositioni

1 Chapter 1 - Getting Started ................. 3 Controller Hardware Overview........................ 4 Control Module Overview............................ 6 Chapter 2 - Controller Setup................. 9 Adjust Display Contrast.............................. 9 Set Controller Date and Time.........................10 Select Time Zone..................................11 Select Auto Daylight Savings Option....................11 Set Maximum Active Station Count.....................12 Sele

Or, to restore defaults to all stations , turn the Lower Line knob to select All Stations. COPY STATION DEFAULTS TO ALL STA's (Press BUTTON) 4. Press and hold the Copy button. Release the button when Copying Done is displayed. CT- COPYING......DONE! 41 Restoring PROGRAM Default Settings A\ Important: Restoring the default Program settings erases and resets all user-defined settings for all programs as follows: 1st Start Time - 12:00am Water Window - 05:00 Water Window - 16:00 Water Day M

The station will shut off when the runtime counts down (or is adjusted down) to 00.0 minutes. Each station will operate in sequence for the selected runtime. Note: To terminate operation, either reduce the station runtime to 00.0 or turn the Function Selector knob momentarily to the OFF position. 63 The Run Function RUN is the Function dial position for normal controller operations. However, automatic controller operation will occur when the Function Selector knob is in any position other th

If not corrected, the 2nd start time will default to the Off mode. Press the Copy button to compare settings. Also refer to the Alerts function on page 44 for additional information. 7. Turn the Upper Line knob right to select the 2nd Start Type screen. The High ET start time option is Off by defualt. To program, turn the Upper Line knob right to display the following setup screen. 2nd Start/Windo........ A V_J 8. Repeat the editing procedure used to enter the 1st start time and water window

2. Connect water supply to either bottom or side inlet.* 3. Seal unused inlet with plug included. 4. Fill hole around sprinkler with gravel, covered by layer of soil. *In cold climates, protect sprinkler from freeze damage by installing a Toro Drain valve (sold separately, Model 53740) to bottom inlet. For new installations, avoid dry spots and areas of over-watering by spacing sprinklers so their spray patterns overlap. Use the guidelines in the accompanying chart and position sprinklers as sho