Log:

Bostitch CAP2000P-OF

Downloads : 3 Arquivo Tamanho: 192 kb    Fabricante : Bostitch  
Categoria : equipamento de bombagem

BOSTITCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty is limited to sales in the United States and Canada. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To obtain warranty service, return th

Bostitch 175869REVA

Downloads : 11 Arquivo Tamanho: 192 kb    Fabricante : Bostitch  
Categoria : equipamento de bombagem

If the motor should overheat, the overload protector will shut the motor off. When the temperature returns to normal, the motor will restart automatically. NOTICE! Do not stop the compressor by pulling out the plug. Use only the On/Off switch, which operates a pressure relief valve on the compressor. If the compressor is plugged in with the switch in the “On” position, the compressor may have trouble restarting against the high pressure which could cause excessive heat build up and could damage

Bostitch N100C

Downloads : 8 Arquivo Tamanho: 270 kb    Fabricante : Bostitch  
Categoria : Pistola de pregos

Contact your Bostitch representative or distributor with any questions concerning the tool and its use. Bostitch, Inc., East Greenwich, Rhode Island 02818. INDEX Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Tool Specifications: Air Consumption & Operating Pressure . . . . . . . . . . . . . . . 4 Air Supply: Fittings, Hoses, Filters, Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Lubrication and Cold Weathe

Bostitch N100CPP

Downloads : 1 Arquivo Tamanho: 270 kb    Fabricante : Bostitch  
Categoria : Pistola de pregos

SUPPLY SOURCE: Use only clean regulated compressed air as a power source for this tool. NEVER USE OXYGEN, COMBUSTIBLE GASES, OR BOTTLED GASES, AS A POWER SOURCE FOR THIS TOOL AS TOOL MAY EXPLODE. REGULATOR: A pressure regulator with an operating pressure of 0 - 125 p.s.i. (0 - 8.79 kg/cm2) is required to control the operatiing pressure for safe operation of this tool. Do not connect this tool to air pressure which can potentially exceed 200 p.s.i. (14 kg/cm2) as tool may fracture or burst, possi

Bostitch N130C

Downloads : 6 Arquivo Tamanho: 270 kb    Fabricante : Bostitch  
Categoria : Pistola de pregos

. . . . . . . . . .Replace quick disconnect fittings Worn piston O-ring . . . . . . . . . . . . . . . . . . . . . .Replace O-ring, check driver Tool dry, lacks lubrication . . . . . . . . . . . . . . . . .Use BOSTITCH Air Tool Lubricant Damaged pusher spring . . . . . . . . . . . . . . . . . .Replace spring Low air pressure . . . . . . . . . . . . . . . . . . . . . . . .Check air supply system to tool Loose magazine nose screws . . . . . . . . . . . . . .Tighten all screws Fasteners too short fo

Bostitch SB-100SX

Downloads : 2 Arquivo Tamanho: 276 kb    Fabricante : Bostitch  
Categoria : Pistola de pregos

Do not use the tool if the arm is not working correctly as accidental driving of a fastener may result. Do not interfere with the proper operation of the contact arm mechanism. Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of fasteners which could cause injury. Do not drive fasteners close to the edge of the work piece as the wood may split, allowing the fastener to be deflected possibly causing injury. This nailer produce

Bostitch N400C

Downloads : 1 Arquivo Tamanho: 488 kb    Fabricante : Bostitch  
Categoria : Pistola de pregos

THE TOOL MUST NOT CYCLE. D. With finger off the trigger, press the contact trip against the work surface. Pull the trigger. THE TOOL MUST CYCLE. MAINTAINING THE PNEUMATIC TOOL When working on air tools, note the warnings in this manual and use extra care evaluating problem tools. REPLACEMENT PARTS: BOSTITCH replacement parts are recommended. Do not use modified parts or parts which will not give equivalent performance to the original equipment. ASSEMBLY PROCEDURE FOR SEALS: When repairing a tool

Bostitch N512C

Downloads : 2 Arquivo Tamanho: 488 kb    Fabricante : Bostitch  
Categoria : Pistola de pregos

The air volume supplied to the tool may be inadequate because of undersize fittings and hoses, or from the effects of dirt and water in the system. Restricted air flow will prevent the tool from receiving an adequate volume of air, even though the pressure reading is high. The results will be slow operation, misfeeds or reduced driving power. Before evaluating tool problems for these symptoms, trace the air supply from the tool to the supply source for restrictive connectors, swivel fittings, lo

Bostitch N401C

Downloads : 0 Arquivo Tamanho: 488 kb    Fabricante : Bostitch  
Categoria : Pistola de pregos

Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a different work area, as accidental actuation may occur, possibly causing injury. LOADING TOOL When loading tool: 1.) Never place a hand or any part of body in fastener discharge area of tool; 2.) Never point tool at anyone; 3.) Do not pull the trigger or depress the trip as accidental actuation may occur, possibly causing injury. OPE

Bostitch 171119REVB

Downloads : 5 Arquivo Tamanho: 488 kb    Fabricante : Bostitch  
Categoria : Pistola de pregos

ASSEMBLY PROCEDURE FOR SEALS: When repairing a tool, make sure the internal parts are clean and lubricated. Use Parker “O”-LUBE or equivalent on all “O”-rings. Coat each “O”-ring with “O”-LUBE before assembling. Use a small amount of oil on all moving surfaces and pivots. After reassembly add a few drops of BOSTITCH Air Tool Lubricant through the air line fitting before testing. AIR SUPPLY-PRESSURE AND VOLUME: Air volume is as important as air pressure. The air volume supplied to the tool may be





categorias