This contains important product dangers, warnings, and cautions. MANUEL DE L’UTILISATEUR ET DE RECETTES POUR WEBER GO-ANYWHERE® & GRILS DE CHARBONS Ne pas jeter. Contient des informations importantes concernant ce produit ; dangers, mises en gardes et precautions. GUIA DEL PROPIETARIO Y RECETAS PARA LOS ASADORES DE CARBON Y GO-ANYWHERE® No lo deseche. Contiene informacion importante sobre los peligros, avisos y precauciones respecto al producto. TABLE OF CONTENTS TABLE OF CONTENTS General Safety

If a gas leak should occur or the LP cylinder should vent in the LP cylinder enclosure, the gas should not be allowed to vent or migrate into the empty or “hollow” area of the “island”. Ventilation openings in the sidewalls of the enclosure should only communicate with the outside of the “island” structure, so that the gas can dissipate outside of the “island” structure. c). If the remote LP cylinder enclosure has four sides, a top and a bottom, and is intended for installation in a built-in “is

If you do not use a Weber® approved regulator the Warranty on the Summit® Built-In Side Burner will be voided. If you have any questions, contact Customer Service at 1-800-446-1071 2) Connect the corrugated gas line to the side burner Connection. Hard piped gas supply top view Figure 1 Cap (Optional Side Burner) Regulator WARNING: You should check for gas leaks every time you disconnect and reconnect a gas fi tting. Note - All factory-made connections have been thoroughly checked for gas leaks.

(See Step "Check for gas leaks.") Note - The hardware size of nuts, bolts and screws is given. For example "1/4-20 x 2 inch bolt" means a bolt 1/4 inch in diameter with 20 threads to the inch, 2 inches long. On a small screw for example, "6-32 x 1/2 inch screw" means a number 6 screw,with 32 threads to the inch, 1/2 inch long. While we give much attention to our products, unfortunately an occasional error may occur. If a part is missing, do not go back to the store. Call the Weber Customer Servi

If bubbles form or if a bubble grows there is a leak. Note- Since some leak test solutions, including soap and water, may be slightly corrosive, all connections should be rinsed with water after checking for leaks. mWARNING: Do not ignite burners when leak checking. Check: a) Hose to manifold connection. Figure 19 (a). b) Regulator to tank connection. Figure 19 (b). mWARNING: If there is a leak at connection (a) retighten the fitting with a wrench and recheck for leaks with soap and water soluti

Figure 16. View from behind cooking box Wing nuts Figure 15 Guide screw Figure 16 Figure 17 h) To reinstall the burners, reverse steps c) through g). mCAUTION: The burner openings must be positioned properly over the valve orifices. Figure 18a. Check proper assembly before fastening manifold in place. Figure 18b. Figure 18 Valve Burner (a) (b) 31 i) Reinstall the Spider Stopper Guards. Slightly rotate the Spider Stopper Guards so that the seams are in line with the Venturi fins. There should be

Contient des precautions de securite avec le produit, des mises en garde et des avertissements. BARBACOA DE CARBON GUIA DEL PROPIETARIO Y RECETAS No desechar. Contiene importantes avisos de peligros, advertencias y precauciones respecto al producto. CHARCOAL GRILL OWNER’S GUIDE & RECIPES Do not discard. This contains important product dangers, warnings, and cautions. BARBACOA DE CARBON GUIA DEL PROPIETARIO Y RECETAS No desechar. Contiene importantes avisos de peligros, advertencias y precaucione

Screw the pipe fitting end of the 3/8 inch flare fitting into the natural gas supply pipe. Tighten with an 11/16 inch wrench. Figure 17 (a). Attach the flare nut on the barbecue gas supply line to the flare fitting end of the 3/8 inch flare fitting. Tighten with a 3/4 inch wrench. Figure 17 (a). Attach the flare nut at the other end of the barbecue gas supply line to the manifold fitting. Tighten with a 3/4 inch wrench. Figure 17 (b). Figure 17 (a) (b) Natural Gas Supply Pipe Pipe fitting end of

Weber may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR SALES SLIP OR INVOICE AND RETURN THE WEBER LIMITED WARRANTY REGISTRATION CARD IMMEDIATELY. This Limited Warranty shall be limited to the repair or replacement of parts which prove defective under normal use and service and which on examination shall indicate This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, vandalism,

As a safety precaution we recommend you check the burner alignment: a) Do the valves fit into the ends of the burners? Figure 13 (a). b) Are the ends of the burners under the washers at the left rear and left front of the cooking box? The screws are only guides. Do not tighten. Figure 13 (b). c) Are the wing nuts under the burner assembly hand tight? Do not tighten with pliers. Figure 13 (c). If you answered YES to a, b and c, the burners are correctly aligned. If you answered NO, the burners ar