THIS MANUAL IS TO BE LEFT WITH THE PROPERTY OWNER. MODELS SW470 AND SW490 ARE FOR VEHICULAR PASSAGE GATES ONLY AND NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE. TABLE OF CONTENTS TABLE OF CONTENTS OPERATOR SPECIFICATIONS Carton Inventory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Operator Dimensions and Specifications . . . . . . . . . . . . . . . . . . .3 UL325 Model Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 OPERATOR WARNINGS Sugge
OPTIONAL AC Adapter Input A Ensure Base Station and PIR Motion Sensor are in close proximity to each other. Press and release Learn Button on Base Station. Buzzer will sound. B Within 60 seconds, press the Learn Button on the inside of the PIR Motion Sensor. LED light will illuminate and Base Station will buzz. Learn Button 1 2 PIR Motion Sensor SWITCH #1: SWITCH #2: 3 4 Learn Button Insert battery pack facing away from circuit board and fasten cover with the smallest screws (provided). NOTE: En
General Information.................................................................................................................3, 4 Features...................................................................................................................................5 Parts Identification...................................................................................................................6, 7 Installation......................................................................
2. If you want the gate to stop when a vehicle drives onto the Interrupt Loop and to close when the vehicle drives off the Interrupt Loop, on switch S1, set SLIDE to OFF and ATG to ON. 3. If you want a closing gate to open when a vehicle drives on the Interrupt Loop, on switch S1, set SLIDE to ON and ATG to OFF. 4. If you want a closing gate to stop when a vehicle drives on the Interrupt Loop and an opening or closing gate to close when the vehicle drives off the Interrupt Loop, on switch S1, se
Model SH-5412 Features • Turns on lighting when motion is detected. • Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Rubber Plug Lamp Holders 2 Shells Cover Plate Gasket 6 Screws (3 sizes included) Mounting Strap Mounting Bolt 2 Wire Plastic Connectors Hanger Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired throug
Barrier gates typically have the fastest open times of the many gate operator types and the slide or swing gates allow you to effectively seal off the perimeter of the complex you are planning to secure. NOTE: Connect all entry devices to the slide or swing gate. If using a device, such as a 7-day timer, to latch the slide or swing gate open during high traffic times, connect the device’s N/O relay output to the control board’s Interrupt Loop input. Once the device activates the Interrupt Loop i
The code between the remote control and the receiver changes with each use, randomly accessing over a billion new codes. The additional push buttons can also activate other garage door openers and/or light controls. (Instructions for programming light products are included with those accessories.) Instructions Are Described and Illustrated Below 1. Press and release the “learn” button on the motor unit. The learn indicator light will glow steadily for 30 seconds. 2. Within 30 seconds, press
Conduit Hole Knockouts for 5/16 in. Knockouts for 3/8 in. 15 in. AUG 10, 2005 WELCOME 3-1/16 in. 9 in. 1-5/8 in. 1-15/16 in. 12 in. 2 in. 7 in. 9-1/2 in. 6 in. 3-1/16 in. 1-1/2 in. 1/2 in. 6 in. 3-15/16 in. 3-1/16 in. 10-1/4 in. 3-1/16 in. 5-1/8 in. Mounting Holes (4) for 5/16 in. 1-1/16 in. Conduit Hole 3 in. Page 2 Dimensions Dimensions Caution! A Static Discharge can Damage Circuit Boards EL2000 Units EL25 Units Bracket Keypad Main Circuit Board Main Circuit Board Connections J200 - Speaker J
The intercoms form an exclusive network and respond only to other intercoms in the network. Intercom (2 in Model LSIS) Rubber Pads (2 in Model LSIS) Operation & Features Channel Select Button: Press the Channel Select button to set intercom to one of four secure channels or the paging channel. The default channel for the intercom is the paging channel where all four channel lights are lit. An intercom on a channel can only hear an intercom on the same channel or on the paging channel. Battery: T
Refer to the manual for all mounting and wiring instructions with the exception of page 14. For page 14, follow instructions shown below. WIRING CONTROL WIRING BATTERY BACKUP If the gate operator is already factory equipped with battery run, only the Right/Left Side switch and Mode 1 are supported (Figure 3). The Right/Left switch must to be set in the same position as the Right/Left switch on the main control board. (See page 22 for correctly setting the Right/Left switch on the control bo