Log:
Sort : Nome ↑   Downloads   Avaliação   Tamanho ↑  

Vanguard Heating UNVENTED (VENT-FREE) PROPANE/LP GAS LOG HEATER

Downloads : 9 Arquivo Tamanho: 533 kb    Fabricante : Vanguard Heating  
Categoria : Eléctrico

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life. — Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supp

Vanguard Heating 000

Downloads : 8 Arquivo Tamanho: 816 kb    Fabricante : Vanguard Heating  
Categoria : Lareiras

— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer,

Vanguard Heating VN3000TB

Downloads : 8 Arquivo Tamanho: 456 kb    Fabricante : Vanguard Heating  
Categoria : Eléctrico

Pressure Testing Heater Gas Connections 1. Open equipment shutoff valve (see Figure 13). 2. Open main gas valve located on or near gas meter. 3. Make sure control knob of heater is in the OFF position. 4. Check all joints from equipment shutoff valve to control valve (see Figure 14). Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak. 5. Correct all leaks at once. 6. Light heater (see Operating Heater, pages ll through 13). Check the rest of the internal joints for

Vanguard Heating GVB35P

Downloads : 7 Arquivo Tamanho: 416 kb    Fabricante : Vanguard Heating  
Categoria : Eléctrico

Max) From External Regulator (11" W.C. Min** to 14" W.C. Max) Pipe Nipple Tee Joint Cap Manual Shutoff Valve * Ground Joint Union Tee Joint 1/8" NPT Plug Tap Reducer Bushing to 1/8" NPTTest Gauge Connection* Preferred construction of inlet gas line Sediment Trap Control Valve Figure 7 - Gas Connection * An A.G.A. design-certified manual shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional A.G.A. design-certified manual shutoff valve from yo

Vanguard Heating VN6B

Downloads : 4 Arquivo Tamanho: 229 kb    Fabricante : Vanguard Heating  
Categoria : Eléctrico

A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly. Continued 13 CONNECTING TO GAS SUPPLY Continued CHECKING GAS CONNECTIONS IMPORTANT: Hold pressure regulator with wrench when connecting it to gas piping and/or fittings. Regulator Heater Cabinet Manual Shutoff Valve * Test Gauge Connection * From Sediment Trap Figure 12 - Gas Connection * An A.G.A. design-certified

Vanguard Heating VN1800TB

Downloads : 2 Arquivo Tamanho: 456 kb    Fabricante : Vanguard Heating  
Categoria : Eléctrico

— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer,

Vanguard Heating VMH26TPC, VMH26TNC

Downloads : 2 Arquivo Tamanho: 816 kb    Fabricante : Vanguard Heating  
Categoria : Lareiras

7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Note: If pilot goes out, repeat steps 3 through 7. This fireplace has a safety interlock system. Wait one (1) minute before lighting pilot again. 8. Turn control knob counterclockwise to desired heating level. The main burner should light. Set control knob to any heat level between HI and LO. CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve. Ignitor Button

Vanguard Heating Gas Log Heater

Downloads : 1 Arquivo Tamanho: 825 kb    Fabricante : Vanguard Heating  
Categoria : Eléctrico

Attach damper clamp so the minimum permanent flue opening will be maintained at all times. Area of Various Standard Round Flues Diameter (ins.) Area (sq. ins.) 5" 6" 7" 8" 20 sq. inches 29 sq. inches 39 sq. inches 51 sq. inches Chimney Height (ft.) Minimum Permanent Flue Opening (sq. ins.) 6' to 15' 15' to 30' 39 sq. inches 29 sq. inches Damper Damper Clamp Damper Clamp Damper Damper Masonry Fireplace Manufactured Fireplace Figure 10 - Attaching Damper Clamp 14 INSTALLING Continued INSTALLING HE

Vanguard Heating 000 to 26

Downloads : 0 Arquivo Tamanho: 816 kb    Fabricante : Vanguard Heating  
Categoria : Lareiras

This makes the front of fireplace flush with wall. An optional trim kit accessory is available (see Accessories, page 30). Trim will extend past sides of fireplace approximately 1/2 inch. This will cover the rough edges of the wall opening. If installing a built-in mantel above the fireplace you must follow the clearances shown in Figure 11, page 12. Follow the instructions below to install the fireplace in this manner. Actual Framing Height 26" 26 7/8" Front Width 26 3/4" 26 7/8" Depth 9 1/2" 1

Vanguard Heating VMH3000TPA

Downloads : 0 Arquivo Tamanho: 779 kb    Fabricante : Vanguard Heating  
Categoria : Eléctrico

INSTALLATION OPTIONS There are three options for mounting this heater. A. Mounting heater to wall B. Mounting heater to optional hearth base C. Mounting heater to optional mantel (some mantels require the hearth base) A. MOUNTING HEATER TO WALL Mounting Bracket The mounting bracket is located in the package tray. Remove mounting bracket from tray. Methods For Attaching Mounting Marking Screw Locations 1. Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is le





categorias