See instruction below: 10 642 97531 Pin Pin Assignment (HD AUDIO) Pin Pin Assignment (AC’97 AUDIO) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MIC Power 4 AVCC 4 NC 5 FRO-R 5 Line Out (R) 6 MIC2_JD 6 Line Out (R) 7 F_IO_SEN 7 NC 8 Key (no pin) 8 Key (no pin) 9 FRO-L 9 Line Out (L) 10 LINE2_JD 10 Line Out (L) Locate the internal audio connectors from your motherboard or sound card. Consult your motherboard or sound card manual for the pin-out positions. 3.5” Device Installation With the front bezel

-Check your motherboard’s CPU socket to ensure its compatibility with the KUHLER H2O. The KUHLER H2O 620 / 920 is compatible with the following CPU sockets: Intel® LGA 1155 / 1156 / 1366 / 2011 AMD® AM2 / AM3 / AM2+ / AM3+ - Be sure to install the KUHLER H2O with the end of the tubes positioned at the bottom of the radiator. 1. Remove the TrueQuiet™ fan mounting pins by pulling slowly on the head of the mounting pin while pushing the tail of the pin through the rear of the case. This ensures tha

(2) UL Class CC or T fast-acting current-limiting type fuses, 200,000 AIC, preferred. Bussman KTK-R, JJN or JJS or equivalent. ( ) Thermomagnetic type breakers preferred. Observe the following when using Ground Fault Circuit Interrupters (GFCIs): • Installation of GFCI only between supplying mains and controller. • The GFCI can be activated by: - capacitive leakage currents between the cable screens during operation (especially with long, screened motor cables) -connecting several controllers to

PSU screws (10) B. Motherboard standoffs (3:4 preinstalled) C. Motherboard screw (9) D. 5.25”/2.5” optional drive screw (10) E. Front panel fan screws (2) F. Drive bay rails for 3.5” (5 pairs) G. Zip ties (2) H. Standard fan screws (4) A H G F E D C B Section 2 Hardware Installation One / One S / One S3 User Manual 2.1 Setting Up When working in your case, please keep the following in mind: . Put the case upright on a flat, stable surface so that the rear panel (power supply and expansion slots)

SYSTEM PROTECTION A variety of industrial-grade safety circuitry will help protect your computer: OVP (Over Voltage Protection), SCP (Short Circuit Protection), and OCP (Over Current Protection). Sometimes the PSU will “latch” into a protected state. You will need to power off the PSU and clear the fault before it will function again. There are no user- replaceable fuses in your CP-1000. SPECIAL QUIET COMPUTING™ PWM FAN A PWM fan can spin much more slowly and be quieter than a voltage-controlled

Make sure you turn the switch to the ON (I) position before you boot up your computer for the first time. In normal operation there is no need to turn the switch to the OFF (O) position since the power supply is equipped with a soft on/off feature, which turns your computer on and off through the soft switch on your computer case. You may need to turn the switch to the OFF position occasionally should your computer crash and you cannot shut it down through use of the soft switch. Installation:

Emergency Stops, over-speed protection, acceleration and deceleration limits, etc must be made by other devices to ensure operation under all conditions. The drive does feature many protection devices which are aimed at protecting the drive and the driven equipment by generating a fault and shutting the drive and motor down by removing power. Mains power variances can also result in shutdown of the drive. When the fault condition disappears or is cleared, the drive can be configured to automatic

As such, it’s possible that your new case may differ slightly from the description in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec’s Computer Enclosures. For more comprehensive instructions on installing the motherboard and peripherals, please refer to the user’s manuals that come with those components. P190 User’s