Dirty cylinder. Worn Bumper. O-rings worn in piston assembly. Disassemble and clean cylinder. Replace bumper. Purchase Bottom Repair Kit Replace piston assembly. On the NBSNC2x4 contact an *AWSC for correct part. All other nailers purchase Bottom Repair Kit. Weak Drive. Inadequate air supply. Worn piston assembly. Check PSI and CFM. Replace piston assembly. On the NBSNC2x4 contact *AWSC for correct part. All other nailers purchase Bottom Repair Kit. NBSNC2X4 leaving a 1/4” indention. Driver blad

SNC1002x4 Pull feeder shoe back into "locked" position. 6. NF2502X4, NB1252X4, NB2002X4, and SNC1002X4 Replace nose cover and latch into place. NBSNC2X4 Replace nose cover. 7. Reload fasteners into magazine. Refer to Feeder Magazine Latch 5. Using pliers remove fasteners. Loading the Tool section in this manual. PAGE 13 FASTENER JAM INSIDE MAGAZINE: SNC1002x4 Pull feeder shoe back into "locked" position. 1. Disconnect tool from air hose. 2. NF2502X4, NB1252X4, NB2002X4, NBSNC2X4 Release the maga

NOTE: The meter housing will be full of liquid so some means should be available to catch what drains from the case and lines. To remove gears (22-25), remove three retaining rings (20) and drive key (21). Withdraw the drive shaft and gear (14), spacer (15), and all parts of bearing and seal assembly (26). Remove the nylon washer from item 26 and note its location. Remove both oilite bearings and both O-rings from bore in register housing. Using new parts, which consist of a new nylon washer, 2

Never use Bleach, Ammonia or Hot water in the unit. The part will have to be replaced, Please email us directly at: customerservice@huskypowerwasher.com. You can also order the part directly at: Check that the circuit is rated at 1 amps or Circuit breaker trips or Fuse blown in Fuse box Extension cord too long or wire size too small Nozzle partially blocked Excessive pressure greater. Make sure the unit is plugged into a dedicated circuit. Use proper extension cord as recommended in Owner’s Manu

4. Flush wand assembly backwards with water or compressed air. 5. If pressure is still too high, repeat steps 2-4. 4. CHECKING OIL: The pump is shipped with the correct amount of oil in it. This pump should never need any oil added or changed unless it develops a leak. A 30 weight non- detergent oil can be used in this pump (approximately 6 oz.). If pump is leaking oil take to an Authorized Service Center. HIGH PRESSURE HOSE: Damaged high pressure hoses can burst which can cause a potentially ha

NOTE: The pressure of the spray on the surface you are cleaning increases as you move the wand closer to the surface. To increase angle to a fan spray, turn counterclockwise To decrease angle to pencil point spray, turn clockwise 4.4 HIGH PRESSURE/TURBO SPRAY Do not move the nozzle to adjust pressure. The high pressure rotary nozzle position is intended for maximum cleaning effect. Keep the spray lance min. 6” to 8” away from the cleaning surface at all times. Rotary Spray USE OF CLEANING CHEMIC

2. Exhaust Muffler-Allows hot exhaust to exit the engine. 3. Siphon Tube & Filter- Used to pick up detergents, degreasers, etc. for cleaning. 4. High Pressure Hose-25' x 1/4" dia. high pressure hose used to transport water from pump to gun. 5. Quick Connect Coupler-Used to attach water hose to pump. 6. Pressure Washer Gun-Used to control flow of water coming from pump. 7. 3.5 HP Tecumseh Engine- This engine is shipped without oil. Included with this pressure washer is a copy of the Engine Manufa

8) © Installing the Handle (see pg. 8) Instalación del mango (ver pág. 8) ©Assembling the Trigger Handle (see pg. 8) Armado de mango del gatillo (ver pag. 8) ©Connecting the High Pressure Hose to the Trigger Handle (see pg. 8) Cómo conectar la manguera de alta presión al mango del gatillo (ver pág. 8) © Connecting the High Pressure Hose to the Pump (see pg. 9) Cómo conectar la manguera de alta presión a la bomba (ver pág. 9) ©Connecting the Garden Hose to the Pressure Washer (see pg.