(Note different types of walls require different types of screws) Fig.8 Prepare and extend the duct cover to your desired height for mounting. Fig.9 Measure and balance the duct cover bracket at the desired height. A Fig. 10 Install the aluminum flex hose to the outlet of the hood. (Flex hose not included) Fig.11 Duct cover will come with “teeth” to be installed into the slot on the hood. Fig. 14 Evenly slide duct cover into the slot of the hood. Fig. 15 Attach duct cover to duct co

(Purchase locally). ► Electrical wire and supplies to comply with local cords. ► Four 1 Va " long flat head wood screws (purchase locally) to mount wood strips. ► Pencil and ruler for marking locations. Saber saw or keyhole saw for cutting the 1 "x2" wood strips to length. D. Accessory Package 1. Wood screws 3/16" x 1" L 6pcs. 2. Wire connector with spring 3pcs. 3. Washer 4pcs. E. Preparing The Range Hood 1. Remove the top electrical Electrical Knockout knockout, you may plan to / b

DUCTING This style of range must be vented via ducting to the outside of the house. Follow general rules when ducting the hood: Use correct size of ducting (6" or 7” round ), do not reduce size of ducting, make all turns gradual, no short corners. If ducting ran will be longer than 10 feet enlarge duct by at least 1" inch diameter after each 10 feet. Tape all joints in ducting and all gasketed openings on hood for a tight seal. For round ducting from the top: For the gray plastic (included) over

As it protects the duct covers from scratches during installation. OPTIONAL (Ductless Recirculating Kit) Air deflector For non-ventedinstallations only, ‘it is highly reconniended always be ventedtothe outside. Charcoal filter Toggle Bolts 2 sets OPTIONAL (Hgh Ceiling Duct Cover Kit) J for higher ceiling ^ \ ^ ° »72 O "* о < 0) Page 4 E. PLANNING FOR THE INSTALLATION AWARNING * Proper installation is your responsibility - Must have a qualified technical to install this range hood. *

pltitr rrad llirtr imfi nctiom roinjilrlrlv. ¡.IMPORTANT SAFETY INSTRUCTIONS-------------------------- ------1 1 SAFETY NOTES.......................................................... .....3 3.TOOLS AND MATERIALS REQUIRED................................. 3 4. INCLUDE THE FOLLOWING PARTS ACCESSORY PACKAGE- . „-3 5. PREPARING THE RANGE HOOD-----------------------------— -----3 6.PREPARING THE INSTALLATION LOCATION.................. ......4 7. PROVIDING ELECTRICAL POWER----------------------

BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. Connect the electrical wires. - Connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to color : black to black, white to white, and green to green as shown on Figure A. - If necessary to hide the electrical wire connections, push wires back into the wiring box. Access the wire connections underneath the

Table of Contents A. Important Safety Instructions ---------------------------P. 1 B. Safety Notes ------------------------------------------------P. 3 C. Tools and Materials Required ----------------------------P. 4 D. Accessory Package ----------------------------------------P. 4 E. Preparing the Range Hood -------------------------------P. 5 F. Preparing the Installation Location ----------------------P. 6 G. Providing Electrical Power --------------------------------P. 7 H. Remove and Reinst

3) *™xi8" screw and flat washer (Fig. 2) DUCTED INSTALLATION METHOD (vented to the outside) 4. Fi nd an opti m al loc ati on fo r the d ud c over's fi x p anel. The f ix p anel must be placed directly above and align with the two body hooks. Drill two more holes insert two toggle bolts. Secure the fix panel with 2 toggle bolts and screw tightly. Be sure to use appropriate anchors for your wall. (figure 4) AWARNING PERSONAL INJURY HAZARD Because of the weight and size of the range hood, tw