This does not apply if the 90° elbows are used to increase or redirect a vertical rise. Figure 12 Example: According to the vent graph (Page 15) the maximum horizontal vent length in a system with a 7Z\x’ (2.3 m) rise is 20’ (6 m) and if a 90° elbow is required in the horizontal vent it must be reduced to 17’ (5.2 m). In Figure 15, dimension A plus B must not be greater than 17’ (5.2 m) • The maximum number of 45° elbows permitted per installation is six (6). These elbows can be installed in eit

For projections exceeding 2-1/2" (64 mm), see Figure 5. For additional vent location restrictions refer to Figure 6 on Page 7. Note -See Figure 36 on Page 20 for the exterior wall recess allowances of the square horizontal termination. Figure 5 6" (152 mm)12" (305 mm) Combustible Projection greater Horizontal Vent Termination Clearances Combustible Projection2-1/2 inches or less in length 18" (457 mm) Ventilated Soffit Unventilated Soffit than 2-1/2 inches in length Termination Kit Side Elevatio

Log placement log placement Figure 63 1. Place rear log (#1) on grate assembly. Log should rest firmly on the two log mounting pins shown. 2. Place top right log (#2) on the rear log. Rest the right back side of the log in the flat area of the rear log. Place the narrow front end of the log next to the center vertical grate bar. 3. Place the top left log (#3) on the rear log. Nest the forked end of the top left log into the fork or the rear log. Rest the narrow end of the top left log behind the

page 26 This installation manual will help you obtain a safe, efficient, dependable installation for your appliance and vent system. Please read and understand these instructions before beginning your installation. PACKAGING The assembled vented gas fireplace heater is packaged with: 1 -one log set shrink-wrapped to the in side surface of the front glass enclosure panel. 2 -one plastic bag containing the literature package which consists of the homeowner's care and operation instructions, instal

In Canada CSA-B149 (1 or 2) Installation Code. CAUTION A listed manual shutoff valve must be installed upstream of the appliance. Union tee and plugged 1/8" NPT pressure tapping point should be installed upstream of the appliance. Figure 41 IMPORTANT: Install main gas valve (equipment shutoff valve) in an accessible location. The main gas valve is for turning on or shutting off the gas to the fireplace. Check your building codes for any special requirements for locating equipment shutoff valve t

Refer to the National Fuel Gas Code and local zoning and code authorities for details on installation requirements. • Mobile home installations must conform with the Mobile Home Construction and Safety Standard, Title 24 CFR, Part 3280 (in Canada CAN/CSA Z240 MH), or, when such a standard is not applicable, the Standard for Mobile Home Installations, ANSI A225.1 -latest edition. • Must be vented directly to the outside in accordance with the latest edition of the National Fuel Gas Code and must

If left unsealed, drafting may cause pilot outage or sooting. Use a heat resistant sealant. Do not seal the chimney flue damper. WARNING Before installing in a solid fuel burning fireplace, The chimney fl ue and firebox must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner. INSTALLING VENTED APPLICATIONS Manual and milli-volt controlled gas logs may be installed as a vented decorative log set in compliance with ANSI Z21.60 and National Fuel Gas Code, Section 6.6

The kits contain seven louvers plus one louver with two pre-drilled holes (eight total) and these instructions. INSTALLATION INSTRUCTIONS Step 1. Turn off the fireplace and allow it to cool before proceeding. Step 2. Slightly lift and pull the existing top louver assembly away from the fireplace. Step 3. Slightly lift up the bottom hinged panel to disengage the small hooks on ether side of the panel. Pull forward and lower the panel down to open. Remove the assembly from the fireplace by rem

P/N 775006M, Rev. J, 04/01 IMPORTANT WARNINGS CAUTION: Read this manual thoroughly before starting installation. For your safety, follow the installation, operation and maintenance instructions exactly without deviation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty. If this appliance is not properly installed, a house fire may result. Contact local building or fire officials about restrictions and installation inspection in your area. 1. If

Rev 1 03/03 CONGRATULATIONS! You have chosen the finest wood burning fireplace available. Your fireplace has been designed for years of heating and viewing enjoyment. Please take time to read this entire manual before installing or operating your fireplace. TABLE OF CONTENTS Listing and Code Approvals............................................................................................................1 Important Information...................................................................