HAZARD RISk OF SERIOUS INjURY OR PROPERTY DAMAGE WHEN TRANSPORTING COMPRESSOR WHAT CAN HAPPEN HOW TO PREVENT IT • Oilcanleakorspillandcouldresultin fire or breathing hazard; serious injury or death can result. Oil leaks will damage carpet, paint or other surfaces in vehicles or trailers. •Alwaysplacecompressoronaprotective mat when transporting to protect against damage to vehicle from leaks. Remove compressor from vehicle immediately upon arrival at your destination. • Always transport and stor

This condensate contains lubricating oil and/or substances which may be regulated and must be disposed of in accordance with local, state, and federal laws and regulations. 1. Set the Auto/Off lever to "Off". 2. Slowly bleed the air from the air tank and air distribution system until tank pressure is approximately 20 psi. 3. Drain water from air tank by opening drain valve on bottom of tank. Risk of bursting. Water will condense in the air tank. If not drained, water will corrode and weaken the

RESPONSIBILITY OF ORIGINAL PURCHASER (initial User): • To process a warranty claim on this product, DO NOT return it to the retailer. The product must be evaluated by an Porter-Cable Authorized Warranty Service Center. For the location of the nearest Porter- Cable Authorized Warranty Service Center call 1-888-559-8550, 24 hours a day, 7 days a week. • Retain original cash register sales receipt as proof of purchase for warranty work. • Use reasonable care in the operation and maintenance of the

Record these numbers in the spaces below and retain for future reference. Model No. __________________________________ Type_______________________________________ Serial No.___________________________________ IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations. Part No. 905067 - 03-21-02 ESPANOL: PAGINA 9 FRANCAISE : PAGE 19 To learn more about Porter-Cable visit our website at: Copyright © 2002

• Do not connect this tool to a system with maximum potential pressure greater than 200 PSI, (13 BAR). • Only connect tool to air supply with a coupling that will release all pressure from the tool when disconnected. • Disconnect tool from air supply and/or remove battery before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, handing the tool to another person, or making adjustments. PREPARING THE TOOL 1. After reading and understanding thi

Maximum compressor pumping time per hour is 30 minutes. STORAGE When you have finished using the air compressor: 1. Set the “ON/OFF” switch to “OFF” and unplug the cord. 2. Review the “Operating Procedures” section. Be sure to drain the water from the air tank. 3. Protect the electrical cord and air hose from damage by winding them loosely around the air compressor. 4. Store the air compressor in a clean and dry location. SPECIFICATIONS MODEL NO. Horsepower SCFM @ 40 psig SCFM @ 90 ps

All repairs made by our service centers are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by others. You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson, Tennessee 38305 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, etc.). ACCESSORIES Since accessories, other than those offered by PORTER-CABLE, have not

• Always keep pressure washer a minimum of four feet away from surfaces (such as houses, automobiles, or live plants) that could be damaged from muffler exhaust heat • Store fuel in an OSHA approved container, in a secure location away from work area. • Do not spray flammable liquids. 3- ENG D25805 • Your washer operates at fluid HOW TO PREVENT IT HAZARD WHAT CAN HAPPEN • Breathing exhaust fumes will cause • Operate pressure washer in a well serious injury or death! ventilated area. Avoid enclos

6. Remove pump mounting screws securing pump (one on each side). 7. Carefully slide pump from brackets and out of the way. 8. Using an adjustable wrench remove the regulator manifold. 9. Apply pipe sealant to new regulator manifold and assemble, tighten with wrench. 10. Reapply pipe sealant to safety valve. 11. Reassemble all components in reverse order of removal. Make sure to orient gauges to read correctly and use wrenches to tighten all components. Pump Mounting Screw 14 - ENG STORAGE STORAG

When the air compressor reaches “cut-out” pressure, the check valve “closes”, allowing air pressure to remain inside the air tank. ON/AUTO - OFF Switch (C) Fig. 3: Turn this switch ON to provide power to the automatic pressure switch and OFF to remove power at the end of each use. Pressure Switch (D) Fig. 1: The pressure switch automatically starts the motor when the tank pressure drops below the factory set “cut-in” pressure. It stops the motor when the air tank pressure reaches the factory s