The RF output changes to the frequency value of the table row containing the cursor and 1.000 000 000 00 is displayed in the AMPLITUDE area of the display. 2. Observe and record the measured value from the power meter. 3. Subtract the measured value from 0 dBm. 4. Move the table cursor over the correction value in row 1. 5. Press Edit Item > enter the difference value from step 3 > dB. The signal generator adjusts the RF output amplitude based on the correction value entered. 6. Repeat ste

Compare the print date of this guide (see bottom of page) with the latestrevision, which can be downloaded from the following websites: Manufacturing Part Number: E8251-90355 Printed in USA February 2008 © Copyright 2006-2008 Agilent Technologies, Inc. Notice The material contained in this document is provided “as is”, and is subject to being changed, without notice, in future editions. Further, to the maximum extent permitted by applicable law, Agilent disclaims all warranties, either express o

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 3. Operation Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Performing a Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Self-Test Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

The service representative’s responsibilities are limited to: • Unpacking the MSD system and verifying that all components are present and undamaged • Connecting the carrier gas line to the instrument from the tank, regulators, and lines previously installed by the customer • Installing, connecting, and turning on MSD system components • Verifying that the system meets Agilent Technologies performance standards • Providing basic user familiarization for system hardware and software • Signi

5 Steps to Install the 82357A............................................................ 7 Step 1: Before You Install the 82357A........................................... 8 Check Your Shipment ............................................................ 8 Check System Requirements ................................................. 9 Step 2: Installing Agilent IO Libraries Suite ................................. 10 Checking for Installed Agilent IO Libraries ........................... 10 Instal

140: Opens an IO path for sending binary data to the signal generator. 150: Creates an ASCII string representation of the number of bytes in the waveform. 160 to 170: Finds the number of digits in Nbytes. 190: Sends the first part of the SCPI command, MEM:DATA along with the name of the file, data_file, that will receive the waveform data. The name, data_file, will appear in the signal generator’s memory catalog. 200 to 210: Sends the rest of the ASCII header. 230: Sends the binary data. Note th

The latest edition comes with the product. 1-2 Installation and Setup Guide /f\Replacing Fuse Fuse Selection Select proper fuse according to the Table 1-2. Table 1-2. Fuse Selection Fuse Rating/Type Fuse Part Number 5A 250Vac UL/CSA type Time Delay 2110-0030 For ordering the fuse, contact your nearest Agilent Technologies Sales and Service Office. T 1 Lever a small minus screwdriver to dismount the fuse holder above the AC line receptacle on the rear panel. To check or replace the fu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Specifications for Frequency and Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

All rights reserved. Agilent® is a registered trademark of Agilent Technologies Inc. Hewlett-Packard® is a registered trademark of Hewlett-Packard Company. LCQ™, LTQ™, LXQ™, MSQ™, TSQ™, and Xcalibur™ are trademarks of Thermo Fisher Scientific Inc. Thermo Fisher Scientific Inc. provides this document to its customers with a product purchase to use in the product operation. This document is copyright protected and any reproduction of the whole or any part of this document is strictly prohibited, e

Differential data encoding can be described by the following equation: transmittedbit i()= databit i( –1).databit i() For a bit-by-bit illustration of the encoding process, see the following illustration: 0 101 00 1 100 101 raw (unencoded) data change = no change = 1111010101111 differentially encoded data 162 Chapter 7 Custom Real Time I/Q Baseband Working with Differential Data Encoding How Differential Encoding Works Differential encoding employs offsets in the symbol table to encode user-def