Be sure to read the “Safety Rules” on Pages 2 and 3, as well as all other safety information in this manual, before attempting to operate this (and related) equipment. • 2.11.1 PRIOR TO INITIAL START-UP ! Prior to initially starting the generator, it must be properly prepared for use. Any attempt to crank or start the engine before it has been properly serviced with the recommended types and quantities of engine fluids (oil, coolant, fuel, etc.) may result in an engine failure. Before starting t

If propane (LP requirements) gas is preferred, contact an authorized service dealer. Refer to Secion 1.12. Recommended fuels should have a Btu content of at least 1,000 Btus per cubic foot for natural gas; or at least 2,520 Btus per cubic foot for LP gas. Ask the fuel supplier for the Btu content of the fuel being used. Fuel pressure for a natural gas set up should be five inches to 14 inches of water column (0.18 to 0.5 psi) at all load ranges. Fuel pressure for an LP vapor set up should be 11

• The engine exhaust fumes contain carbon monoxide, which can be DEADLY. This dangerous gas, if breathed in sufficient concentrations, can cause unconsciousness or even death. For that reason, adequate ventilation must be provided. Exhaust gases must be piped safely away from any building or enclosure that houses the generator to an area where people, animals, etc., will not be harmed. This exhaust system must be installed properly, in strict compliance with applicable codes and standards. • Kee

187699 Revision I (12/14/2000) Visit our Generac website: A This is the alert symbol. It is usedto alert you to potential personal injury hazards. Obey all safety safetysafety messagesthat follow this symbol to avoid possible injury or death. Generac Portable Products 2,400 PSIHigh PressureWasher EQUIPMENT DESCRIPTION CONGRATULATIONS on your purchase of a GENERAC high pressure washer. It has been designed, engineered and manufactured to give you the best possible dependability and performance. T

(3) Any warranted, emissions-related part that is scheduled for replacement as required maintenance in the Owner’s Manual shall be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part shall be repaired or replaced by Generac according to Subsection (4) below. Any such emissions-related part repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warra

Excessive exposure can be harmful to your health. Excessive exposure can produce a rapid pulse, light-headedness, weakness or fainting. If you become uncomfortable or experience any of the above conditions exit the steambath immediately. Steambaths can put undue stress on the body. Therefore a steambath should be used only under a doctor's direction if you: Are pregnant Have a heart condition Have high blood pressure Have circulatory problems Are under the influence of alcohol Are under the inf

AK and 3K Series with R30K Control Owners Manual page 2 SECTION 3: TROUBLESHOOTING GUIDE The Troubleshooting Guide beiow is meant as a general aid only. There are no user serviceable parts in the generator All repairs should be performed by a qualified service person For additional assistance or the factory authorized service person nearest you call AMEREC's Service Department at 1 -800-331 -0349 SYMPTOMS PROBABLE CAUSES ACTION TO BE TAKEN Control 'ON' (Control Liolitod) no Steam No water to

SWAGEFORM 17 032300 1 HOLDER, FUSE 56 057593 4 MOUNT, CABLE TIE 18 022668 1 FUSE, AGC-30 57 028739 4 WRAP, TIE-4" LONG 19 076020 1 SWITCH, TOGGLE DPDT 58 061979 1 BUS, BAR 20 074074 ** ASSEM. POTTED REG. WOFIN 59* 0A2833 1 HARNESS, PANEL "PP" IP 21 067680 ** VOLTAGE REG. ASSEM. B&D 60* 0A2833A 1 HARNESS, PANEL "PP" 3P 22 075476 ** SCREW, PPHM M4-0.7 x 16MM 61 064009 1 PILOT LIGHT RED 14-V. 23 022264 ** WASHER, LOCK #8-M4 63 081988 1 DECAL-EXERCISE INFO 24 022237 1 WASHER, LOCK 3/8" 65 086381 2 C

Scald Hazard: Do Not Touch the steam head or trim during operation as they are HOT. Stay at least 12 inches away from the hot steam escaping from the steam head. Be careful when entering a steambath. Escaping steam from an overheated steam room may cause injury. AK Series w/K60 Control Owners Manual page 2 SECTION 1A: STEAM GENERATOR OVERVIEW The standard K60 model steam generator control the steam room and an optional secondary steam'' feature automatically engages cutting features an adjustabl