Failure to do so can result in serious injury. “THANKS!!” From all the employees of Poulan/Weed Eater, we say thank you for your purchase! This American made product was designed to give you many years of satisfactory use when operated and maintained according to the instructions in this manual. Please read and follow these instructions to attain optimum performance and maximum lifetime from your unit. POULAN/WEED EATER DIVISION WHITE CONSOLIDATED INDUSTRIES, INC. Shreveport, Louisiana 7113

Do not let starter rope snap back. Hold the handle and let the rope rewind slowly. NOTE: Do not attempt to cut material with the fast idle lock button in the locked position. STARTING A COLD ENGINE (or warm engine after running out of fuel) ON/STOP SWITCH ON STOP (SIDE VIEW) 1. Move ON/STOP switch to the ON position. 2. Pull choke knob out to the full extent. 3. Slowly press primer bulb 6 times. 4. Squeeze and hold throttle trigger. With thumb press fast idle lock down; then release throttle tri

If you run the saw at full throttle without a cutting load, unnecessary wear can occur to the chain, bar, and engine. It is recommended that the engine not be operated for longer than 30 seconds at full throttle. S To avoid losing control when cut is complete, do not put pressure on saw at end of cut. S Stop the engine before setting the saw down after cutting. TREE FELLING TECHNIQUES WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near

SPARK PLUG REFERENCE GUIDE 78 F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE SHOP MANUAL USE TITLE SHOP MANUAL USE 613GC SERVICE MANUAL Shop Manual Use This manual contains all the technical information necessary for carrying out repairs on the 613GC cut-off saw. For safe, efficient work, it is of prime importance that the values indicated be adhered to. Routine periodic maintenance is covered in the operator’s manual included with each cut-off saw. General Shop Rules • Always use the right tool

Water in engine can result in shortened engine life. 14 15 CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower. 4. Connect spark plug wire to spark plug. Replace safety ignition key. WARNING: To avoid serious injury, before performing any service or ad just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key. 3. Make sure the augers and all mov ing parts have completely stopped. 4. Remove safety ignition key

Please do not return unit to retailer. • 1-800-554-6723 Instruction Manual Manual de Instrucciones Manuel d'lnstructions 1950 / 1975 / 2050 / 2055 / 2075 2150 / 2155 / 2175 / 2350 / 2375 2050WT / 2150PR For Occasional Use Only & & WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. ADVERTENCIA: Lea et manual de instrucciones y siga todas Ias advertencias e enstrucciones de seguridad. Et no hacerlo puede re

961 95 00-01 22 18 21 53 19 28 19 55 28 19 55 54 54 6 6 5 6 6 9 12 7 7 8 6 11 27 27 30 26 25 20 23 24 31 25 24 26 23 29 21 53 19 20 18 10 4 13 14 16 15 36 37 50 47 42 44 27 43 46 38 45 4327 41 42 40 39 34 32 49 19 48 51 33 35 56 REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 10530SBE (96195000101), PRODUCT NO. 961 95 00-01 KEY PART NO. NO. DESCRIPTION 4 532 19 10-79 Pulley, Impeller 532 18 89-09 Bearing Assembly, Flange 6 532 15 53-77 Nut, Hex Flange 5/16-18 7 532 18 03-

Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Store unit with all guards in place. Position so that any sharp object cannot accidentally cause injury to passersby. Store the unit out of reach of children. S Before storing, drain all fuel from the unit. Start engine and allow to run until it stops. S Clean the unit before storing. Pay particular attention to the air intake area, keeping it free o

5 END CAP COVER ASSEMBLY SUPPORT POST MOUNTING BRACKET LANCED TABS BRACKET SUPPORT PIN RETAINER SPRING MOUNTING TO TRACTOR (See Fig. 5) Use Hardware - - GROUP "D" NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting assembly to tractor. 1. Raise seat on tractor to allow assembly to be mounted. 2. With cover closed, lift assembly and place support post inside mounting bracket. Allow assembly to rest on lanced tabs of mounting bracket. 3. Line up holes

4. Partially plugged muffler. 4. Remove and clean muffler. 5. Improper carburetor adjustment. 5. Adjust carburetor to richer position. Excessive bounce/ diffi cult handling 1. Ground too dry and hard. 1. Moisten ground or wait for more favorable soil conditions. Soil balls up or clumps 1. Ground too wet. 1. Wait for more favorable soil conditions. Engine runs but tiller won’t move 1. Drive control bar is not engaged. 2. V-belt not correctly adjusted. 3. V-belt is off pulley(s). 1. Engage drive c