ALL ductwork should be smooth inside with no projections from sheet metal screws or other obstructions, which will collect lint. When adding ducts, the duct to be added should overlap the duct to which it is to be connected. ALL ductwork joints must be taped to prevent moisture and lint from escaping into the building. Inspection doors should be installed at strategic points in the exhaust ductwork for periodic inspection and cleaning of lint from the ductwork. NOTE: When the exhaust ductwork pa

• Sort load batches properly and select proper temperature and cycle settings. • Avoid overloading, adding wet clothes to a partially dry load and over drying. • If you have multiple loads to dry, try to dry one load after another right away to take an advantage of a warm dryer. This way you already have a warm dryer and you save some time for drying. • Do not open door needlessly because it causes warm/hot air to escape; which prolongs drying time. • Use dryer during low humidity because it wil

DryTimeDry Time For 'High' and 'Low' mode,you can choosedrying time freely. For 'Air Dry' mode, only 30or 60 areavailable. Attention Please choose thedrying time andTemperatureaccording to thequality and quantityof the garments. Heating apparatus won't heat in'Air dry' mode, and isproper for down, sweater, mohair, cottonsweater, cotton-padded clothes. Youmay choose this mode tomake garments fluffier after dried. The machine can also achieve same results for garments left unused for long in thewa

PROGRAM LOCATION 02 (PL02) Number of Auto Peaks (Dryness Level) PL02 PERM PRESS drYL (Wait 3-Seconds) Number of Peaks Decrease (“Hold In” to Accelerate) (“Hold In” to Accelerate) Number of Peaks Increase PERM PRESS 25 PL03 LO TEMP HI TEMP Summary: The dryness level is programmable from a minimum of 1 to a maximum of 99. 32 F. PROGRAM LOCATION 03 (PL03) HI temp PL03 PERM PRESS HI.F (Wait 3-Seconds) (Temperature Decrease) (Temperature Increase) PERM PRESS 180.F HI TEMP LO TEMP (Automatically goes

Avoid using screws on any objects which will protrude inside the exhaust ducting and catch lint. An extremely long run of exhaust ducting or exhaust ducting with many turns in it will result in reduced airflow through the dryer, causing poor dryer performance. If this is the case, an auxiliary fan may have to be installed to boost the exhaust airflow. CAUTION: IMPROPERLY SIZED OR INSTALLED EXHAUST DUCT WORK CAN CREATE A POTENTIAL FIRE HAZARD. IMPORTANT: DO NOT USE SCREENS OR CAPS ON THE OUTSI

No. Part No. Qty. Description 1 160015 1 High Security MK-100 Lock Assembly with Key (for coin models Only) 160017 1 Special Dummy Lock ONLY (for non-coin models Only) 160104 1 MK-100 Key ONLY 2 160052 1 Lock Cam ONLY 3 881053 1 ADC Logo with Tape 870011 1 Double Sided Tape Kit 4 882511 1 White High Security Control Door Assembly Less Lock (includes illus. nos. 4 and 5) 882513 1 Almond “B” High Security Control Door Assembly Less Lock (includes illus. nos. 4 and 5) 882512 1 Coral Blue High Secur

However, a preoperational test should be performed before the dryer is publicly used. It is possible that adjustments have changed in transit or due to marginal location (installation) conditions. Turn on electric power to the dryer. Refer to the operating instructions for starting your dryer. Open all shutoff valves. When a gas dryer is first started (during initial start-up), it has a tendency not to ignite on the first ignition attempt. This is because the gas supply piping is filled with

. . . . . . . . . . . . . . . . . 35 Special accessories . . . . . . . . . . . ........ . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Drainage kit . . . . . . . . . . . . . . . . . ........ . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Stacking kit . . . . . . . . . . . . . . . . . ........ . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Index . . . . . . . . . . . . . . . . . . . . . . . ........ . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Service & s

Openings must be equally divided at the top and bottom of the door and airflow must be unobstructed. A louvered door with equivalent air openings for the length of the door is acceptable. 10 English LOCATION OF YOUR DRYER IN A CLOSET OR RECESSED AREA Following are instructions concerning and the minimum clearances required for any closet, recessed area, or customized under-counter installation: • Additional distances facilitate installation and servicing. • Addtional clearances might be r