Freeze Protection If the temperature sensors detect a drop to below 44.F/6.7.C within the heater, the pump will automatically activate to provide freeze protection. The equipment stays on until 4 minutes after the sensors detect that the spa temperature has risen to 45.F/7.2.C or higher. 9 Spa Maintenance The maintenance and care of your spa is simple and easy to carry out, and if performed regularly as scheduled, problems will be minimal. It is important that the following procedures be read th

(repair or replacement) Spa Surface: 3 years Strong Spas warrants the original retail purchaser the surface integrity of the spa against blistering or delaminating as a result of defects in material or workmanship for a period of 3 years. (repair or replacement) Plumbing: 3 years Strong Spas warrants the original retail purchaser the integrity of the spas plumbing against leaks as a result of defects in material or workmanship for a period of 3 years. (parts and labor)3 Equipment: 2 years Strong

This spa must be on adedicated circuit. CAUTION: OWNER’S MANUAL ™ More than one GFCIused on the electricalcircuit will render thisspa inoperable. This spa must be on adedicated circuit. P.O. Box 108 Northumberland, PA 17857 1-800-STRONG-9 1-800-787-6649 1/9/07 Table of Contents Introduction ................................................................................................................................. 1 Safety Instructions.........................................................

If the mineral content deviates from prescribed pH level (7.2-7.8) deposits on the spa walls, filter, electric heating element or gas heater manifold and piping may adversely affect the condition of your spa equipment. Since the water capacity of your spa is far less than that of a swimming pool, the chemical reaction caused by the presence of one or more persons in the spa is more rapid and pronounced. In other words, it is much more difficult to maintain the proper pH balance in a spa than in

OWNER’S MANUAL Patriot ™ 3204 Point Township Drive (Rte 11) • P.O. Box 108 Northumberland, PA 17857 1-800-STRONG-9 1-800-787-6649 12/20/06 Table of Contents Introduction ................................................................................................................................. 1 Health Safety.............................................................................................................................. 2 Installation -Spa placement ............................

Solution: If the problem persists, contact your dealer or service organization. 8 Troubleshooting continued from previous page Problem: A significant difference between temperature sensors has been detected. This could indicate a flow problem. Solution: Check water level in spa. Refill if necessary. If water level is okay, make sure the pumps have been primed. If problem persists, contact your dealer or service organization. Problem: Persistent low flow problems. (Displays on the fifth occurrenc

If the opposite direction is desired, release the button and let the display revert to the current water temperature. Press the button to display the set temperature, and again to make the temperature change in the desired direction. after 3 seconds, the LCD will stop flashing and display the current temperature. Light There are several color options in our spas and by pressing the light button in quick succession the customer can cycle through the different lighting options. BEFORE START UP! IM

This type of chemical can be added in quantities of 0.5 ounce per 500 gallons of spa water. Check the chlorine level at least seven hours or more after adding to determine the full effect of the added chemical. Liquid chlorine is not recommended. ORGANIC POLYMERS - are used in various forms. These chemicals clear up cloudy or dirty water appearance and prevent calcium deposits on the inside spa finish, plumbing and heating equipment. Use as recommended by the manufacturer. METAL GON - or its equ

The filter cycle begins six (6) minutes after the spa is energized. The second filter cycle begins 12 hours later. Filter duration is programmable for 2, 4, 6, 8 hours of for continuous filtration (indicated by FILC). The default filter time is 2 hours. To program, press “Temp” then “Jets”. Press “Temp” to adjust. Press “Jets” to exit programming. The default filter time is 2 hours. Troubleshooting No power to spa: 1. Check proper connection of to pack 2. Check fuse in pack. 3. Must have very go

Long exposure at higher temperature can result in dizziness and/or hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98°F (36.7°C). The symptoms of hyperthermia include dizziness, fainting, drowsiness or lethargy. The affects of hyperthermia include: • Unawareness of impending hazard • Failure to perceive heat • Failure to recognize the need to exit the spa • Physical inability to exit the spa • Fetal